glsl-sse2 is a header-only abstraction library aimed providing the comfort of GLSL programming language and efficiency of SSE2. In short, it is an optimized SIMD vector library that behaves like the GLSL shading language.

SSE2 is a very powerful extension used in the ia32 and amd64 instruction set often overlooked by many programmers who are seeking a performance boost for their applications.

The programmers who are aware of SSE, either lack the knowledge and know-how to fully utilize it, or are forced to write unportable, unmaintainable assembly code, or use SSE intrinsics. SSE intrinsic based code quality depends heavily on the compiler's quality and very often produces poor quality code that it's scalar equivalent will out-perform (for more information on the subject, see http://www.liranuna.com/?p=984).

glsl-sse2 takes care of all the nasty stuff while providing the familiar API of GLSL - no ugly assembly no cache misses due to bad compiler output and no need to resort to unmaintainable or unportable code.

glsl-sse2 is geared toward performance, and will do it's best to signal the compiler how to best utilize the situation at hand: This example of a cross product between two vec4s (this code assumes the w component is meaningless):

vec4 cross(const vec4 &a, const vec4 &b)
{
    return a.yzxw * b.zxyw - a.zxyw * b.yzxw;
}

would be converted to this assembly code using glsl-sse2 and GCC 4.4:

_Z5crossRK4vec4S1_:
    movaps    (%rsi), %xmm1
    movaps    (%rdx), %xmm2
    pshufd    $201, %xmm1, %xmm5
    pshufd    $210, %xmm2, %xmm0
    pshufd    $210, %xmm1, %xmm4
    pshufd    $201, %xmm2, %xmm3
    mulps     %xmm0, %xmm5
    mulps     %xmm3, %xmm4
    subps     %xmm4, %xmm5
    movaps    %xmm5, (%rdi)
    ret

Minimal instructions and compiler hints help GCC to output a hand-written quality assembly code, complete with instruction pairing and little overhead.

glsl-sse2 is already written in a way that will try and make the compiler output the best possible code. However, some compilers are unable to produce the best possible code - compilers that ignore instruction pairing hints and parallel operations. It is best to avoid those compilers if you are seeking high performance. Most notable compiler that produces poor code is MSVC 2008 and below.

Another factor that will effect code performance is the architecture. glsl-sse2 will be most effective in a 64bit environment where there are double the SSE registers to operate on, causing less register pressure, as well as a guarentee of SSE2 being present - without the need to check CPUID (although most, if not all, CPUs today support SSE2 which was released in 2001, a decade ago!).

Currently the project is in a stable state, however it had not been subjected to real-world (ab)use yet. You are welcome to try it at your own risk, and file bug reports, if such are found.

Because of alignment issues, only direct SSE2 compatible types will be implemented. Types such as vec3, mat3 and types that depend on those, will not be implemented.

If you need an unsupported type, simply use a bigger one - you will still get the best out of the vectorization power of SSE (there are, of course, several exceptions, such as mat2 and vec2, depending on the operations performed).

• GNU C Compiler 4.x and above
• Microsoft Visual C++ 2008 and better
• Intel C++ Compiler 10.0 and above
• clang 2.8
• llvm-gcc using DragonEgg 2.8

Since not all compilers are equal, and behave differently, glsl-sse2 does its best to try and make most of the compilers output similar code. However some compilers take hints better than others. These compilers are best suited to extract most performance out of glsl-sse2, ordered from best to worst:

• Intel C++ Compiler 12.0+
• GNU C Compiler 4.4+
• Microsoft Visual C++ 2010+
• clang 2.8 / DragonEgg

The use of LLVM compilers (clang, dragonegg) is highly discouraged, as LLVM does not output code that makes good use of instruction pairing, which can result a flat 100% speed increase when used correctly (such as ICC/GCC).

• Downswizzle dvec4 => dvec2 (Circular dependency issues)
• Refactor swizzling, it's a mess (new_swizzle branch only works on GCC 4.4)
• Conversion functions between vectors
• Missing classes: dmat2x4, dmat4x2
• Better tests
• Namespacing
• Complete rewrite of bvec4
  • swizzling of booleans
  • bvec4 generators for all vector classes
• Exponential functions for vec4, dvec4
• Trigonometric functions for vec4, dvec4
• Division for ivec4, uvec4