Yatoom/setup.md

Thinkfan setup

Note: I configured this thinkfan setup for my old Thinkpad w520 on Ubuntu 17.10.

1. Install necessary programs

Install lm-sensors and thinkfan.

sudo apt-get install lm-sensors thinkfan

2. Setup configuration

Find the temperature control devices with

find /sys/devices -type f -name "temp*_input"

Add them to /etc/thinkfan.conf, including (level, min_temperature, max_temperature):

hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp3_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp4_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp5_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp1_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp2_input

(0,	0,	60)
(1,	60,	65)
(2,	65,	70)
(3,	70,	75)
(4,	75,	80)
(5,	80,	85)
(7,	85,	32767)

3. Enable fan control

echo "options thinkpad_acpi fan_control=1" > /etc/modprobe.d/thinkfan.conf
modprobe thinkpad_acpi

You can check with lsmod if thinkfan_acpi is running
To reload a module you need to remove it with sudo modprobe -r <module>, but this is not always possible, so we might need a reboot here.

4. Testing and running

To test thinkfan, use:

thinkfan -n

And to run it, use:

sudo service thinkfan start

And to retrieve the status, use:

service thinkfan status

5. Running on startup

To make it run at startup, we need to edit /etc/modules and add the lines below, to make the modules thinkpad_acpi and coretemp load at boot time. The thinkpad_acpi has to be loaded before coretemp.

thinkpad_acpi
coretemp

Note that this may change the /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp*_input paths (hwmon3 can become hwmon2 or vice versa), probably because of the order in which the modules are loaded or something. So, in the /etc/thinkfan.conf config, you might need to update these lines.

Furthermore, we need to enable the thinkfan service via systemctl.

sudo systemctl enable thinkfan.service

woolfg · 2019-11-18T20:20:33Z

thanks +1 , just helped me to setup thinkfan on my T440s

managervcf · 2020-05-07T10:53:18Z

Thanks! It helped with my X1C6.

lukaspour · 2020-05-13T16:05:29Z

@managervcf HI, can you please share your x1c6 config?

Thanks! It helped with my X1C6.

managervcf · 2020-05-16T09:53:11Z

@lukaspour

HI, can you please share your x1c6 config?

Actually, I have changed the thinkfan.conf file recently because of /proc/acpi/ibm/thermal consisting of 8 temperatures on battery and 16 temperatures on AC.

Every time I plugged/unplugged AC and rebooted, I got an unexpected behavior or an error from the thinkfan.service saying:

ERROR: Sensor /proc/acpi/ibm/thermal has 8 temperatures, but you have 16 correction values for it.

This variable number of temperatures (8 on battery vs 16 on AC) didn't let me use the simple syntax below.

tp_thermal /proc/acpi/ibm/thermal (0, 0, 0, 0, 0, 0, 0, 0, 0, 0, -66, 0, 0, 0, 0, 0)

(0,	0,	50)
(1,	50,	60)
(2,	60,	65)
(3,	65,	70)
(4,	70,	75)
(5,	75,	80)
(6,	80,	85)
(7,	85,	32767)

As I couldn't find any relevant info about this problem online, I tried experimenting with the complex example syntax (/usr/share/doc/thinkfan/examples/thinkfan.conf.complex).

Finally, this config below fixed my problem of variable number of temperatures to correct. Of course, fan levels and min/max thresholds are just an example that happens to work for my machine. I hope it will help you or anyone having a simiar problem.

######################################################################
## thinkfan 0.9 example config file
## ================================
##
## ATTENTION: There is only very basic sanity checking on the configuration.
## That means you can set your temperature limits as insane as you like. You
## can do anything stupid, e.g. turn off your fan when your CPU reaches 70°C.
##
## That's why this program is called thinkfan: You gotta think for yourself.
##
#######################################################################
##
## This file shows how to use sensor-specific temperature limits.
## First of all, you need to specify temperature inputs. On a Thinkpad, you can
## just use:
##
tp_thermal /proc/acpi/ibm/thermal  # provides us with 16 temperature inputs

##
## On other systems, you have to specify a file in /sys/class/hwmon for each
## sensor you want to use. They are numbered in their order of appearance.
## For example:
#
# hwmon /sys/class/hwmon5/temp2_input           #1
# hwmon /sys/class/hwmon0/device/temp3_input    #2
#
## If you want to read temperatures directly from the hard disk, thinkfan needs
## to be compiled with -DUSE_ATASMART. Then you can do:
#
# atasmart /dev/sda                             #3
# ...
#
## You can have as many temperature inputs as you like. You should at get the
## temperature from the CPU, the GPU and the hard disk.
#

#
## Next we specify the fan we want to use. On a Thinkpad, this is:
#
tp_fan /proc/acpi/ibm/fan

#
## On anything other than a Thinkpad you'll probably use some PWM control file
## in /sys/class/hwmon. Remember that fan levels range from 0 to 255 and that
## they're just a number, not including the word "level" as seen below.
## A sysfs fan would be specified like this:
#
# pwm_fan /sys/class/hwmon/hwmon2/device/pwm1
#
## But remember you can only have one fan.

#
## Then you need to specify the temperature limits for each of the sensors.
## A dot means that the corresponding sensor should be ignored. The length of the
## UPPER and LOWER limits must be the same as the number of temperatures. In this
## example, /proc/acpi/ibm/thermal contains 16 sensors (on older thinkpads,
## there may be only 8), some of which are unused (hence the dots).
## A sysfs temperature input always contains only one sensor, so if you specify
## 5 sysfs files above, the length of your limits must be 5, too.
#
## I've come up with these preliminary settings for my Thinkpad T61p. They probably
## don't make sense for anything else, so you most definitely have to work
## something out for yourself.
#


{ "level 0"   # the fan level
# ^-------^   This works for /proc/acpi/ibm/thermal.
#             for a PWM fan in /sys/class/hwmon it would have to be just
#             0 or "0".
#
#    Sensor count:
#    1  2  3  4  5  6  7  8  9  10 11 12 13 14 15 16
#    ==============================================
    (0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0)      # LOWER limit
    (50	.  .  .  .  .  .  .  .  .  .  .  .  .  .  .)      # UPPER limit
}


{ "level 1"
# ^-------^ For a PWM fan you may have to use something around 30 to get the
# same speed.
    (50 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (55 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 2"
    (55 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (60 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 3"
    (60 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (65 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 4"
    (65 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (70 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 5"
    (70 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (75 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 6"
    (75 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (80 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level 7"
    (80 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (85 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

{ "level disengaged" # nice idea: "level auto" can also be used.
                     # but again: only numbers for sysfs.
    (85 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
    (99 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .)
}

cohnt · 2020-07-01T20:23:54Z

Used this to help get thinkfan running on my P53. Thank you for sharing!

dsboo · 2020-12-13T06:33:34Z

thanks very much i use this on my t480s:)

sebfoucault · 2021-01-04T19:20:57Z

thanks very much i use this on my t480s:)

Hi @dsboo, Any specific adaptation for t480s that would be valuable to share ?

kendoori · 2021-02-10T15:08:37Z

@managervcf your variant worked for me on my T480. It's been super difficult to get updated config for modern TPs

jasonwert · 2021-02-12T12:57:19Z

@managervcf Thanks so much! This works great for me on a T440p using Kde Neon, I just had to change to 8 sensors from 16.

grssnbchr · 2021-04-20T13:40:59Z

@managervcf Thanks, I'm using your config, but I still get the following error:

You have configured more temperature limits than sensors. That doesn't make sense.
Refusing to run without usable config file!

This is because sometimes my /proc/acpi/ibm/thermal has 8 readings, sometimes it has 16 (and it doesn't actually matter whether on AC or BAT). So I thought your config covers that variability.. maybe I'm doing something wrong?

uguremirmustafa · 2021-07-05T08:38:59Z

This was helpful! I use it with my L14 gen1.

jheled · 2021-08-02T20:19:28Z

Can someone tell me how to get the system fan control running again after I started thinkfan?

I tried 'sudo systemctl stop thinkfan', but the fan control remains off, and even
manually setting the fan (echo level 7 | sudo tee /proc/acpi/ibm/fan) fails to start the fan.

Thanks, Joseph

ghost · 2021-08-02T21:49:27Z

Can someone tell me how to get the system fan control running again after I started thinkfan?

I tried 'sudo systemctl stop thinkfan', but the fan control remains off, and even
manually setting the fan (echo level 7 | sudo tee /proc/acpi/ibm/fan) fails to start the fan.

Thanks, Joseph

After you execute the echo command please provide output fom ¨cat /proc/acpi/ibm/fan' command.

printf '%s' 'level 7' > /proc/acpi/ibm/fan
cat /proc/acpi/ibm/fan

monosoul · 2021-10-17T12:50:13Z

Wrote an article with a configuration example for ThinkPad P14s (Gen 2) and a bit of deep dive into configuration settings: https://blog.monosoul.dev/2021/10/17/how-to-control-thinkpad-p14s-fan-speed-in-linux/

johnsidoli · 2022-04-17T23:13:01Z

Is there any way I can check that thinkfan is running when I reboot? I think I've done everything correctly and even tested it, as per this excellent new answer on askubuntu (which uses new undeprecated codes): https://askubuntu.com/a/1139409/1587772

fakamaz · 2022-07-08T08:07:53Z

Hi All,

After doing all the above and with settings like that, fans are still not rolling... granted temperature is in 50, but still...

hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp3_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp4_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp1_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp5_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp2_input
hwmon /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp1_input
hwmon /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp2_input

(0, 0, 40)
(1, 40, 44)
(2, 44, 48)
(3, 48, 52)
(4, 52, 56)
(5, 56, 60)
(6, 60, 64)
(7, 64, 68)
(127, 68, 32767)

While running "status" one of the lines shows this:
Jul 08 09:58:15 ThinkPad-L430 thinkfan[15995]: WARNING: Using default fan control in /proc/acpi/ibm/fan.

EDIT: Managed to fix default fan control and now it's not stating an error, but fans are not working anyway...

So how to start them? Thanks in advance.

williamzerner · 2022-10-10T10:27:46Z

Hi, my laptop model is S230u but when i run the command
find /sys/devices -type f -name "temp*_input"`

I am not getting (level, min_temperature, max_temperature). Is my device incompatible? I am on Ubuntu 22.04.1 LTS

hareldev · 2022-10-18T08:15:24Z

Hello,
Following the comment of step number 5. - (hwmon3 can become hwmon2 or vice versa), and as hwmon is updated with every reboot, I created this script to run at startup, and update the /etc/thinkfan.conf file respectively:
https://github.com/hareldev/cmd-utils/tree/main/thinkfan

justarandomuser · 2022-10-31T06:34:39Z

Thinkpad T15g gen 1

Suggested config:

hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp6_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp3_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp7_input
# hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp4_input
# hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp8_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp1_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp5_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp2_input
# /sys/devices/pci0000:00/0000:00:1d.0/0000:55:00.0/nvme/nvme0/hwmon3/temp3_input
# /sys/devices/pci0000:00/0000:00:1d.0/0000:55:00.0/nvme/nvme0/hwmon3/temp1_input
# /sys/devices/pci0000:00/0000:00:1d.0/0000:55:00.0/nvme/nvme0/hwmon3/temp2_input
hwmon /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp1_input
hwmon /sys/devices/virtual/thermal/thermal_zone9/hwmon7/temp1_input
hwmon /sys/devices/virtual/thermal/thermal_zone7/hwmon4/temp1_input

(0,	0,	40)
(1,	40,	55)
(2,	55,	70)
(3,	70,	75)
(4,	75,	80)
(5,	80,	85)
(7,	85,	32767)

matteyeux · 2022-10-31T12:13:21Z

T14 Gen 3 suggested config :

hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp6_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp3_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp7_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp4_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp1_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5/temp5_input


(0, 0 , 39)
(1, 39, 52)
(2, 51, 55)
(3, 54, 58)
(4, 56, 66)
(5, 64, 70)
(6, 68, 80)
(7, 79, 86)
(127, 84, 32767)

mat127 · 2022-12-02T09:15:19Z

My P15v Gen 1 (Fedora 37) /etc/thinkfan.conf:

sensors:
  - hwmon: /sys/class/hwmon
    name: thinkpad
    indices: [1, 2, 3, 4, 5, 6, 7]

  - hwmon: /sys/class/hwmon
    name: thinkpad
    indices: [8]
    optional: true

  - hwmon: /sys/class/hwmon
    name: coretemp
    indices: [1, 2, 3, 4, 5]

  - hwmon: /sys/class/hwmon
    name: nvme
    indices: [1]

  - hwmon: /sys/class/hwmon
    name: acpitz
    indices: [1]

  - hwmon: /sys/class/hwmon
    name: pch_cometlake
    indices: [1]

  - hwmon: /sys/class/hwmon
    name: iwlwifi_1
    indices: [1]
    optional: true

fans:
  - tpacpi: /proc/acpi/ibm/fan

levels:
  - [0, 0, 60]
  - [2, 60, 65]
  - [3, 65, 70]
  - [5, 70, 75]
  - [6, 75, 80]
  - [7, 80, 85]
  - ["level disengaged", 85, 255]

panapnamana · 2023-04-21T08:29:08Z

Hello, Following the comment of step number 5. - (hwmon3 can become hwmon2 or vice versa), and as hwmon is updated with every reboot, I created this script to run at startup, and update the /etc/thinkfan.conf file respectively: https://github.com/hareldev/cmd-utils/tree/main/thinkfan

I am using this. Thank you for your work!

matteyeux · 2023-04-21T08:31:08Z

Hello,

fyi zcfan does the job : https://github.com/cdown/zcfan

DenGontsov · 2023-05-30T19:50:46Z

For Lenovo ThinkPad T460s
Suggested config:

hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp6_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp3_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp7_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp4_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp8_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp1_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon6/temp5_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp3_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp1_input
hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp2_input
hwmon /sys/devices/virtual/thermal/thermal_zone2/hwmon5/temp1_input
hwmon /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp1_input
hwmon /sys/devices/virtual/thermal/thermal_zone1/hwmon4/temp1_input

(0, 0, 40)
(1, 40, 44)
(2, 44, 48)
(3, 48, 52)
(4, 52, 56)
(5, 56, 60)
(6, 60, 64)
(7, 64, 68)
(127, 68, 32767)

reddare · 2023-08-02T19:29:39Z

Thinkpad T14 G3 (AMD) Arch:

sensors:
  - hwmon: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon5
    name: thinkpad
    indices: [1, 3, 5, 6, 7]

  - hwmon: /sys/devices/pci0000:00/0000:00:18.3/hwmon/hwmon6
    name: k10temp
    indices: [1]

  - hwmon: /sys/devices/pci0000:00/0000:00:02.4/0000:03:00.0/nvme/nvme0/hwmon4
    name: nvme
    indices: [1, 2, 3]

  - hwmon: /sys/devices/virtual/thermal/thermal_zone0/hwmon1
    name: acpitz
    indices: [1]

fans:
  - tpacpi: /proc/acpi/ibm/fan
 
levels:
  - [0, 0, 52]
  - [1, 52, 60]
  - [2, 60, 65]
  - [level auto, 65, 75]
  - [level disengaged, 75, 255]

theopaid · 2023-10-13T19:09:22Z

Thank you for this guide!! I used the config that @reddare posted above for my new T14 G4 AMD and it's great. :)

Some notes:

At 3. when you say "You can check with lsmod if thinkfan_acpi is running", you probably meant thinkpad_acpi
I did not have to edit the '/etc/modules' file to make it work (Arch|Gnome|systemd-boot)

amirrezaalavi · 2023-11-15T15:59:40Z

ThinkPad T490 Intel GPU:

sensors:
  - hwmon: /sys/class/hwmon/hwmon1/temp1_input
fans:
  - tpacpi: /proc/acpi/ibm/fan
levels:
  - [0, 0, 53]
  - [1, 52, 60]
  - [2, 59, 68]
  - [3, 65, 70]
  - [4, 69, 75]
  - [5, 74, 80]
  - [6, 79, 85]
  - [7, 84, 86]
  - ["level full-speed", 85, 32767]

bizonek27 · 2023-11-15T19:18:19Z

ThinkPad T15g - Options

sensors:
  ######### Common CPU - Option 1 with GPU #########

  # GPU - [2] is a GPU - not used by me
  #- tpacpi: /proc/acpi/ibm/thermal
  #  name: GPU
  #  indices: [2]

  # CPU
  #- tpacpi: /proc/acpi/ibm/thermal
  #  name: CPU
  #  indices: [1]

  ######### Common CPU - Option 2 with GPU #########
  # CPU
  #- hwmon: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon9/temp1_input
  # GPU
  #- hwmon: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon9/temp2_input


  ######### Common CPU - Option 3 without GPU #########
  # Package id 0
  #- hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp1_input

  # CPU per Core
  # Core 0
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp2_input
  # Core 1
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp3_input
  # Core 2
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp4_input
  # Core 3
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp5_input
  # Core 4
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp6_input
  # Core 5
  - hwmon: /sys/devices/platform/coretemp.0/hwmon/hwmon11/temp7_input
    #name: coretemp
    #indices: [1, 2, 3, 4, 5, 6, 7]

  ######### GPU nouveau #########
  #- hwmon: /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/hwmon/hwmon7/temp1_input
    #name: nouveau
    #indices: [1]

  ######### SSD nvme0 #########
  #- hwmon: /sys/devices/pci0000:00/0000:00:1b.0/0000:02:00.0/nvme/nvme0/hwmon3/temp1_input
  #- hwmon: /sys/devices/pci0000:00/0000:00:1b.0/0000:02:00.0/nvme/nvme0/hwmon3/temp2_input
  #- hwmon: /sys/devices/pci0000:00/0000:00:1b.0/0000:02:00.0/nvme/nvme0/hwmon3/temp3_input
    #name: nvme
    #indices: [1, 2, 3]
    #correction: [-5, 0, 0]

  ######### SSD nvme1 #########
  #- hwmon: /sys/devices/pci0000:00/0000:00:1d.0/0000:55:00.0/nvme/nvme1/hwmon4/temp1_input
  #- hwmon: /sys/devices/pci0000:00/0000:00:1d.0/0000:55:00.0/nvme/nvme1/hwmon4/temp2_input
    #name: nvme
    #indices: [1, 2]

  ######### acpitz #########
  - hwmon: /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp1_input
    #name: acpitz
    #indices: [1]

  # cometlake
  - hwmon: /sys/devices/virtual/thermal/thermal_zone4/hwmon8/temp1_input
    #name: pch_cometlake
    #indices: [1]

  # iwlwifi
  - hwmon: /sys/devices/virtual/thermal/thermal_zone10/hwmon12/temp1_input
    #name: iwlwifi_1
    #indices: [1]

fans:
  - tpacpi: /proc/acpi/ibm/fan

levels:
  - [0, 0, 52]
  - [1, 52, 60]
  - [2, 60, 65]
  - ["level auto", 65, 75]
  - ["level disengaged", 75, 255]

Testing


Temperatures(bias): 55(0), 54(0), 53(0), 52(0), 51(0), 51(0), 51(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 58(-3), 67(-6), 58(-2), 59(-3), 57(-2), 57(-2), 56(-1), 55(0), 59(0) -> Fans: level 2
Temperatures(bias): 54(0), 56(0), 55(0), 54(0), 55(0), 54(0), 58(-1), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 53(0), 56(0), 54(0), 54(0), 53(0), 53(0), 55(0), 56(0), 60(0) -> Fans: level 2
Temperatures(bias): 53(0), 55(0), 54(0), 54(0), 54(0), 53(0), 56(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 55(0), 57(0), 55(0), 55(0), 55(0), 54(0), 56(0), 56(0), 60(0) -> Fans: level 2
Temperatures(bias): 53(0), 56(0), 55(0), 54(0), 54(0), 54(0), 56(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 53(0), 56(0), 55(0), 54(0), 54(0), 54(0), 56(0), 57(0), 60(0) -> Fans: level 2
Temperatures(bias): 54(0), 57(0), 56(0), 55(0), 55(0), 54(0), 57(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 54(0), 57(0), 56(0), 55(0), 55(0), 54(0), 57(0), 56(0), 60(0) -> Fans: level 2
Temperatures(bias): 54(0), 57(0), 56(0), 55(0), 54(0), 54(0), 57(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 55(0), 59(0), 57(0), 56(0), 57(-1), 56(0), 57(0), 57(0), 60(0) -> Fans: level 2
Temperatures(bias): 55(0), 58(0), 56(0), 56(0), 56(0), 56(0), 57(0), 56(0), 59(0) -> Fans: level 1
Temperatures(bias): 56(0), 58(0), 57(0), 57(0), 57(0), 55(0), 57(0), 56(0), 60(0) -> Fans: level 2

5nizza · 2023-12-11T13:50:12Z

Just a note: on my X1YogaGen7 I was getting errors

ERROR: Module thinkpad_acpi doesn't seem to support fan_control
ERROR: ~TpFanDriver: Resetting fan control in /proc/acpi/ibm/fan: Invalid argument

To resolve them, use

echo "options thinkpad_acpi fan_control=1 experimental=1" > /etc/modprobe.d/thinkfan.conf

instead of the original line without experimental=1. The issue may be related to the laptop having two fans instead of one (or maybe not).

And here is my config file, inspired by @managervcf. It works on thinkpad x1 yoga G7:

##
## This file shows how to use sensor-specific temperature limits.
## First of all, you need to specify temperature inputs. 
##
tp_thermal /proc/acpi/ibm/thermal  # provides 8 temperature inputs on x1 yoga G7, and only the first value is relevant

#
## Next we specify the fan we want to use. On a Thinkpad, this is:
#
tp_fan /proc/acpi/ibm/fan

#
## Then you need to specify the temperature limits for each of the sensors.
## A dot means that the corresponding sensor should be ignored. The length of the
## UPPER and LOWER limits must be the same as the number of temperatures. In this
## example, /proc/acpi/ibm/thermal contains 8 sensors, some of which are unused (hence the dots).
#

{ "level 0"   # the fan level
# ^-------^   This works for /proc/acpi/ibm/thermal.
#
#    Sensor count:
#    1  2  3  4  5  6  7  8
#    ======================
    (0  0  0  0  0  0  0  0)      # LOWER limit
    (53	.  .  .  .  .  .  .)      # UPPER limit
}


{ "level 1"
    (48 .  .  .  .  .  .  .)
    (60 .  .  .  .  .  .  .)
}

{ "level 2"
    (55 .  .  .  .  .  .  .)
    (65 .  .  .  .  .  .  .)
}

{ "level auto"
    (60 .  .  .  .  .  .  .)
    (99 .  .  .  .  .  .  .)
}

Probably there is no need for level 0, level 1, level 2, level auto separation,
and a simpler separation level 0, level auto will do just fine,
as my goal is to avoid the fan kicking in too early.

ellyq · 2024-10-31T18:45:55Z

T14s Gen4 (AMD)

# ThinkPad ACPI
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon8/temp1_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon8/temp3_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon8/temp4_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon8/temp6_input
hwmon /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon8/temp7_input

# AMD GPU
hwmon /sys/devices/pci0000:00/0000:00:18.3/hwmon/hwmon7/temp1_input
hwmon /sys/devices/pci0000:00/0000:00:08.1/0000:c3:00.0/hwmon/hwmon6/temp1_input

# SSD
hwmon /sys/devices/pci0000:00/0000:00:02.4/0000:02:00.0/nvme/nvme0/hwmon3/temp3_input
hwmon /sys/devices/pci0000:00/0000:00:02.4/0000:02:00.0/nvme/nvme0/hwmon3/temp1_input
hwmon /sys/devices/pci0000:00/0000:00:02.4/0000:02:00.0/nvme/nvme0/hwmon3/temp2_input

# WiFi
hwmon /sys/devices/pci0000:00/0000:00:02.2/0000:01:00.0/ieee80211/phy0/hwmon9/temp1_input

# acpitz
hwmon /sys/devices/virtual/thermal/thermal_zone0/hwmon1/temp1_input

tp_fan /proc/acpi/ibm/fan
(0, 0, 37)
(1, 35, 42)
(2, 40, 45)
(3, 43, 47)
(4, 45, 52)
(5, 50, 57)
(6, 55, 72)
(7, 68, 82)
("level full-speed", 77, 32767)

	######################################################################
	# thinkfan 0.7 example config file
	# ================================
	#
	# ATTENTION: There is only very basic sanity checking on the configuration.
	# That means you can set your temperature limits as insane as you like. You
	# can do anything stupid, e.g. turn off your fan when your CPU reaches 70°C.
	#
	# That's why this program is called THINKfan: You gotta think for yourself.
	#
	######################################################################
	#
	# IBM/Lenovo Thinkpads (thinkpad_acpi, /proc/acpi/ibm)
	# ====================================================
	#
	# IMPORTANT:
	#
	# To keep your HD from overheating, you have to specify a correction value for
	# the sensor that has the HD's temperature. You need to do this because
	# thinkfan uses only the highest temperature it can find in the system, and
	# that'll most likely never be your HD, as most HDs are already out of spec
	# when they reach 55 °C.
	# Correction values are applied from left to right in the same order as the
	# temperatures are read from the file.
	#
	# For example:
	# tp_thermal /proc/acpi/ibm/thermal (0, 0, 10)
	# will add a fixed value of 10 °C the 3rd value read from that file. Check out
	# http://www.thinkwiki.org/wiki/Thermal_Sensors to find out how much you may
	# want to add to certain temperatures.

	# Syntax:
	# (LEVEL, LOW, HIGH)
	# LEVEL is the fan level to use (0-7 with thinkpad_acpi)
	# LOW is the temperature at which to step down to the previous level
	# HIGH is the temperature at which to step up to the next level
	# All numbers are integers.
	#

	# I use this on my T61p:
	#tp_fan /proc/acpi/ibm/fan
	#hwmon /proc/acpi/ibm/thermal (0, 10, 15, 2, 10, 5, 0, 3, 0, 3)
	#hwmon /sys/devices/virtual/hwmon/hwmon0/temp1_input

	hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp3_input
	hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp4_input
	hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp5_input
	hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp1_input
	hwmon /sys/devices/platform/coretemp.0/hwmon/hwmon3/temp2_input

	(0, 0, 60)
	(1, 60, 65)
	(2, 65, 70)
	(3, 70, 75)
	(4, 75, 80)
	(5, 80, 85)
	(7, 85, 32767)

Yatoom/setup.md

Thinkfan setup

1. Install necessary programs

2. Setup configuration

3. Enable fan control

4. Testing and running

5. Running on startup

woolfg commented Nov 18, 2019

managervcf commented May 7, 2020

lukaspour commented May 13, 2020

managervcf commented May 16, 2020

cohnt commented Jul 1, 2020

dsboo commented Dec 13, 2020

sebfoucault commented Jan 4, 2021

kendoori commented Feb 10, 2021

jasonwert commented Feb 12, 2021

grssnbchr commented Apr 20, 2021 •

edited

Loading

uguremirmustafa commented Jul 5, 2021

jheled commented Aug 2, 2021

ghost commented Aug 2, 2021 •

edited by ghost

Loading

monosoul commented Oct 17, 2021

johnsidoli commented Apr 17, 2022

fakamaz commented Jul 8, 2022 •

edited

Loading

williamzerner commented Oct 10, 2022

hareldev commented Oct 18, 2022

justarandomuser commented Oct 31, 2022

matteyeux commented Oct 31, 2022

mat127 commented Dec 2, 2022 •

edited

Loading

panapnamana commented Apr 21, 2023

matteyeux commented Apr 21, 2023

DenGontsov commented May 30, 2023

reddare commented Aug 2, 2023

theopaid commented Oct 13, 2023 •

edited

Loading

amirrezaalavi commented Nov 15, 2023 •

edited

Loading

bizonek27 commented Nov 15, 2023

5nizza commented Dec 11, 2023 •

edited

Loading

ellyq commented Oct 31, 2024

Yatoom/setup.md

Thinkfan setup

1. Install necessary programs

2. Setup configuration

3. Enable fan control

4. Testing and running

5. Running on startup

woolfg commented Nov 18, 2019

managervcf commented May 7, 2020

lukaspour commented May 13, 2020

managervcf commented May 16, 2020

cohnt commented Jul 1, 2020

dsboo commented Dec 13, 2020

sebfoucault commented Jan 4, 2021

kendoori commented Feb 10, 2021

jasonwert commented Feb 12, 2021

grssnbchr commented Apr 20, 2021 • edited Loading

uguremirmustafa commented Jul 5, 2021

jheled commented Aug 2, 2021

ghost commented Aug 2, 2021 • edited by ghost Loading

monosoul commented Oct 17, 2021

johnsidoli commented Apr 17, 2022

fakamaz commented Jul 8, 2022 • edited Loading

williamzerner commented Oct 10, 2022

hareldev commented Oct 18, 2022

justarandomuser commented Oct 31, 2022

matteyeux commented Oct 31, 2022

mat127 commented Dec 2, 2022 • edited Loading

panapnamana commented Apr 21, 2023

matteyeux commented Apr 21, 2023

DenGontsov commented May 30, 2023

reddare commented Aug 2, 2023

theopaid commented Oct 13, 2023 • edited Loading

amirrezaalavi commented Nov 15, 2023 • edited Loading

bizonek27 commented Nov 15, 2023

5nizza commented Dec 11, 2023 • edited Loading

ellyq commented Oct 31, 2024

grssnbchr commented Apr 20, 2021 •

edited

Loading

ghost commented Aug 2, 2021 •

edited by ghost

Loading

fakamaz commented Jul 8, 2022 •

edited

Loading

mat127 commented Dec 2, 2022 •

edited

Loading

theopaid commented Oct 13, 2023 •

edited

Loading

amirrezaalavi commented Nov 15, 2023 •

edited

Loading

5nizza commented Dec 11, 2023 •

edited

Loading