• This warehouse currently only maintains the version of LilyGo that is on sale , For the LilyGo discontinued version of the LoRa board, please jump to Archive package to download
• Arduino IDE users need to configure the board to be used in the <utilities.h> file in the sketch directory before using the example. The <utilities.h> file contains the pin definitions of the board. If you do not select it, an error will occur during compilation.

./examples/
├── ArduinoLoRa                              # Only support SX1276/SX1278 radio module
│   ├── LoRaReceiver
│   └── LoRaSender
├── Display                                  # Only supports TBeam TFT Shield
│   ├── Free_Font_Demo
│   ├── TBeam_TFT_Shield
│   ├── TFT_Char_times
│   └── UTFT_demo
├── GPS                                      # T-Beam GPS demo examples
│   ├── TinyGPS_Example
│   ├── TinyGPS_FullExample
│   ├── TinyGPS_KitchenSink
│   ├── UBlox_BasicNMEARead                  # Only support Ublox GNSS Module           
│   ├── UBlox_NMEAParsing                    # Only support Ublox GNSS Module           
│   ├── UBlox_OutputRate                     # Only support Ublox GNSS Module      
│   └── UBlox_Recovery                       # Only support Ublox GNSS Module      
├── LoRaWAN                                  # LoRaWAN examples
│   ├── LMIC_Library_OTTA
│   └── RadioLib_OTAA
├── OLED
│   ├── SH1106FontUsage
│   ├── SH1106GraphicsTest
│   ├── SH1106IconMenu
│   ├── SH1106PrintUTF8
│   ├── SSD1306SimpleDemo
│   └── SSD1306UiDemo
├── PMU                                      # T-Beam & T-Beam S3 PMU demo examples
├── RadioLibExamples                         # RadioLib examples,Support SX1276/78/62/80...
│   ├── Receive_Interrupt
│   └── Transmit_Interrupt
├── Sensor                                   # Sensor examples,only support t-beams3-supreme
│   ├── BME280_AdvancedsettingsExample
│   ├── BME280_TestExample
│   ├── BME280_UnifiedExample
│   ├── PCF8563_AlarmByUnits
│   ├── PCF8563_SimpleTime
│   ├── PCF8563_TimeLib
│   ├── PCF8563_TimeSynchronization
│   ├── QMC6310_CalibrateExample
│   ├── QMC6310_CompassExample
│   ├── QMC6310_GetDataExample
│   ├── QMC6310_GetPolarExample
│   ├── QMI8658_BlockExample
│   ├── QMI8658_GetDataExample
│   ├── QMI8658_InterruptBlockExample
│   ├── QMI8658_InterruptExample
│   ├── QMI8658_LockingMechanismExample
│   ├── QMI8658_MadgwickAHRS
│   ├── QMI8658_PedometerExample
│   ├── QMI8658_ReadFromFifoExample
│   └── QMI8658_WakeOnMotion
|── T3S3Factory                              # T3 S3 factory test examples
└── BPFFactory                               # T-Beam BPF factory test examples

1. Install Arduino IDE

2. Install Arduino ESP32

3. Copy all folders in the lib directory to the Sketchbook location directory. How to find the location of your own libraries, please see here

   • Windows: C:\Users\{username}\Documents\Arduino
   • macOS: /Users/{username}/Documents/Arduino
   • Linux: /home/{username}/Arduino

4. Open the corresponding example

   • Open the downloaded LilyGo-LoRa-Series
   • Open examples
   • Select the sample file and open the file ending with ino

5. On Arduino ISelect the corresponding board in the DE tool project and click on the corresponding option in the list below to select

   Click to view T-Beam S3 Supreme Arduino IDE options

   T-Beam S3 Supreme	Value
   Board	ESP32S3 Dev Module
   Port	Your port
   USB CDC On Boot	Enable
   CPU Frequency	240MHZ(WiFi)
   Core Debug Level	None
   USB DFU On Boot	Disable
   Erase All Flash Before Sketch Upload	Disable
   Events Run On	Core1
   Flash Mode	QIO 80MHZ
   Flash Size	8MB(64Mb)
   Arduino Runs On	Core1
   USB Firmware MSC On Boot	Disable
   Partition Scheme	8M Flash(3M APP/1.5MB SPIFFS)
   PSRAM	QSPI PSRAM
   Upload Mode	UART0/Hardware CDC
   Upload Speed	921600
   USB Mode	CDC and JTAG
   Programmer	Esptool

   Click to view T-Beam-V1.X Arduino IDE options

   T-Beam-V1.X	Value
   Board	ESP32 Dev Module
   Port	Your port
   CPU Frequency	240MHZ(WiFi/BT)
   Core Debug Level	None
   Erase All Flash Before Sketch Upload	Disable
   Events Run On	Core1
   Flash Frequency	80MHZ
   Flash Mode	QIO
   Flash Size	4MB(32Mb)
   JTAG Adapter	Disabled
   Arduino Runs On	Core1
   Partition Scheme	Default 4M Flash with spiffs(1.2M APP/1.5MB SPIFFS)
   PSRAM	Enable
   Upload Speed	921600
   Programmer	Esptool

   Click to view LoRa32 V1.x or T3 TCXO Arduino IDE options

   T-Beam-V1.X	Value
   Board	ESP32 Dev Module
   Port	Your port
   CPU Frequency	240MHZ(WiFi/BT)
   Core Debug Level	None
   Erase All Flash Before Sketch Upload	Disable
   Events Run On	Core1
   Flash Frequency	80MHZ
   Flash Mode	QIO
   Flash Size	4MB(32Mb)
   JTAG Adapter	Disabled
   Arduino Runs On	Core1
   Partition Scheme	Default 4M Flash with spiffs(1.2M APP/1.5MB SPIFFS)
   PSRAM	Disable
   Upload Speed	921600
   Programmer	Esptool

   Click to view T3-S3 Arduino IDE options

   T3-S3	Value
   Board	ESP32S3 Dev Module
   Port	Your port
   USB CDC On Boot	Enable
   CPU Frequency	240MHZ(WiFi)
   Core Debug Level	None
   USB DFU On Boot	Disable
   Erase All Flash Before Sketch Upload	Disable
   Events Run On	Core1
   Flash Mode	QIO 80MHZ
   Flash Size	4MB(32Mb)
   Arduino Runs On	Core1
   USB Firmware MSC On Boot	Disable
   Partition Scheme	Default 4M Flash with spiffs(1.2M APP/1.5MB SPIFFS)
   PSRAM	QSPI PSRAM
   Upload Mode	UART0/Hardware CDC
   Upload Speed	921600
   USB Mode	CDC and JTAG
   Programmer	Esptool

   Click to view T-Motion Arduino IDE options

   T-Motion	Value
   Board	Nucleo-64
   Port	Your port
   Debug symbols and core logs	None
   Optimize	Smallest (-Os default)
   Board part number	Nucleo L073RZ
   C Runtime Library	Newlib Nano (default)
   Upload method	STM32CubeProgrammer (DFU)
   USB support (if available)	CDC (generic 'Serial' supersede U(S)ART)
   U(S)ART support	Enabled (generic 'Serial')
   USB speed (if available)	Low/Full Speed

   • To upload a sketch, you need to hold down the BOOT button on the board and then plug in the USB. At this time, it will enter the DFU mode to allow program writing.
   Click to view T3-C6 Arduino IDE options

   T3-S3	Value
   Board	ESP32C6 Dev Module
   Port	Your port
   USB CDC On Boot	Enable
   CPU Frequency	160MHZ(WiFi)
   Core Debug Level	None
   USB DFU On Boot	Disable
   Erase All Flash Before Sketch Upload	Disable
   Flash Mode	DIO
   Flash Size	4MB(32Mb)
   Arduino Runs On	Core1
   USB Firmware MSC On Boot	Disable
   Partition Scheme	Default 4M Flash with spiffs(1.2M APP/1.5MB SPIFFS)
   Upload Speed	921600
   Programmer	Esptool

   Click to view T-Beam PBF Arduino IDE options

   T3-S3	Value
   Board	ESP32S3 Dev Module
   Port	Your port
   USB CDC On Boot	Enable
   CPU Frequency	240MHZ(WiFi)
   Core Debug Level	None
   USB DFU On Boot	Disable
   Erase All Flash Before Sketch Upload	Disable
   Flash Mode	QIO 80Mhz
   Flash Size	16MB(128Mb)
   Arduino Runs On	Core1
   USB Firmware MSC On Boot	Disable
   Partition Scheme	16M Flash (3MB APP/9.9MB FATFS)
   PSRAM	OPI PSRAM
   Upload Speed	921600
   Programmer	Esptool

6. Please uncomment the utilities.h file of each sketch according to your board model, otherwise the compilation will report an error.

7. Upload sketch

To access TTN (The Things Network), please refer to LilyGo_LoRa_Series_Quick_Start

• T-Beam SoftRF
• T-Beam Paxcounter
• T-Beam Meshtastic

• T-Beam Supreme schematic
• AXP2101 datasheet
• SX1262 datasheet
• GSP MAX-M10 datasheet
• PCF8563 datasheet
• QMI8658 datasheet
• QMC6310 datasheet
• BME280 datasheet

• T-Beam_V1.2 schematic
• AXP192 datasheet
• SX1262 datasheet
• GSP NEO-6/NEO-8 datasheet

• T3_S3_V1.2 schematic
• SX1262 datasheet
• SX1278 datasheet
• SX1276 datasheet
• SX1280 datasheet

T3_V1.6.1 schematic

T3_V1.3 schematic

T-Motion schematic

T3-C6 schematic

T3-TCXO schematic

1. T-Beam Supreme GPS backup power comes from 18650 battery. If you remove the 18650 battery, you will not be able to get GPS hot start. If you need to use GPS hot start, please connect the 18650 battery.

2. There is no data output from the GPS. Refer to GPS factory reset

3. How to find the pin definition?

   Click to view detailed

   • Each sketch contains <utilities.h>, and all board pins are written in this file

4. Can’t upload sketches?

   Click to view detailed

   1. Connect the board USB to the computer
   2. Press the BOOT button and hold (If there is no BOOT button, you need to keep GPIO0 connected to GND.)
   3. Press the RST button
   4. Release the RST button
   5. Finally release the BOOT button(If there is no BOOT button, you need to disconnect GPIO0 from GND.)
   6. Click to upload the program

5. After setting the output power of LoRa, you need to set the minimum current. Set up sx1262 as follows:

   Click to view detailed

   // set output power to 10 dBm (accepted range is -17 - 22 dBm)
   if (radio.setOutputPower(22) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
       Serial.println(F("Selected output power is invalid for this module!"));
       while (true);
   }
   // set over current protection limit to 80 mA (accepted range is 45 - 240 mA)
   // NOTE: set value to 0 to disable overcurrent protection
   if (radio.setCurrentLimit(80) == RADIOLIB_ERR_INVALID_CURRENT_LIMIT) {
       Serial.println(F("Selected current limit is invalid for this module!"));
       while (true);
   }

6. Precautions for using SX1280 PA version

   Click to view detailed

   • When using the SX1280 PA module, it is recommended that the software controls the 1280 chip to output 2~5dbm, so that the entire module will output 20dbm power; When the output of the 1280 chip is higher than 2dbm, the output power of the entire module is only 20dbm; When the output of the 1280 chip is higher than 5dbm, the output power of the entire module is only 20dbm, but if 5dbm is given to the FEM, it will damage the FEM chip (the maximum input allowed by the FEM is 5dbm) If the output of the 1280 chip is lower than 2dbm, the output power of the entire module is within 20dbm.
   • T3-S3 PA version SX1280 output power setting cannot be greater than 2~5dbm, otherwise the FEM chip may be damaged. Setting 3dbm already has 20dmb output power

7. How to identify the LoRa model?

   Click to view detailed

   • To identify the LoRa model, you only need to check the sticker on the board. 433MHz is SX1278, 868MHz is SX1276, and if the label says SX1262, it is SX1262.

8. Why does Serial not have any output?

   • Arduino -> Tools -> USB CDC On Boot -> Enable

9. T-Beam-s3-supreme antenna signal quality

   Click to view detailed