How To Restore an Antique Door

Restoring an antique door can breathe new life into your home, preserving its historical charm while improving functionality. This process requires patience, attention to detail, and the right techniques to achieve stunning results. In this guide, we’ll walk you through the steps to restore an antique door, covering everything from initial assessment to the final finishing touches. This Old House expert Tom Silva demonstrates the restoration process on a door believed to be original to a 1918 home.

*Unless otherwise noted, costs in this article reflect an average of prices that our team found from hardware stores like Lowes and Home Depot, and on Amazon.com.

Assess the Antique Door’s Condition

Before diving into the restoration process, evaluate the door’s current state. This assessment will help you determine the extent of work required and identify any potential challenges that may lie ahead.

Identify Common Issues

Antique doors often encounter several problems due to age and wear:

• Cracked or lifting veneer
• Damaged or outdated hardware
• Paint or varnish buildup
• Sun damage and fading
• Warping or misalignment

Test for Lead

When working with old doors, it’s essential to test for lead in the paint or varnish. Silva emphasizes the importance of this step to ensure safety during the restoration process. Use a lead testing kit available at most hardware stores to check for lead before proceeding with any sanding or stripping.

Preparing the Antique Door

Proper preparation is key to achieving a successful restoration. This stage involves removing the door from its hinges and stripping away old finishes and hardware.

Remove the Door and Hardware

Take these steps to begin:

1. Carefully remove the door from its hinges to avoid damage.
2. Take off all hardware, including knobs, locks, and hinges.
3. Label and store hardware in a safe place if you plan to reuse it.

Strip Old Finishes

To remove old paint or varnish effectively:

1. Apply a water-based paint stripper generously to the door’s surface.
2. Allow the stripper to sit for 30–45 minutes, covering it with plastic wrap to prevent evaporation.
3. Use a putty knife or scraper to remove the loosened finish.
4. Clean residue with a brass brush and water to ensure a smooth surface.

Silva demonstrates this process, emphasizing the importance of using eco-friendly, low-VOC strippers for indoor use.

Repairing Damage to an Antique Door

Once the door is stripped, you can address any damage or imperfections that may have accumulated over the years.

Fix Veneer Issues

For damaged or lifting veneer:

1. Carefully cut away the damaged sections.
2. Apply wood filler to smooth out the surface.
3. Sand the filled areas to blend seamlessly with the surrounding wood.

Patch Holes and Cracks

To repair holes from old hardware or cracks in the wood:

1. Use epoxy wood filler for small repairs to ensure durability.
2. For larger holes, cut a plug from matching wood and glue it in place.
3. Sand the repaired areas smooth to create an even surface.

In his demonstration, Silva repairs a hole in an old deadbolt using a hole saw and epoxy glue.

Enhancing Antique Door Structure with New Veneer

If the door’s surface is severely damaged, applying new veneer can give it a fresh look while preserving its structure.

Select the Right Veneer

Choose a veneer that matches the door’s original wood species or complements your home’s style. Silva uses a mahogany peel-and-stick veneer to achieve a classic finish.

Application Process

Take your time with these important steps:

1. Cut the veneer into strips for each panel, stile, and rail for precise fitting.
2. Peel back a small portion of the backing and align the veneer accurately.
3. Slowly remove the backing while pressing the veneer in place to avoid air pockets.
4. Use a roller to smooth out any bubbles, working from the center outward.
5. Trim excess veneer with a sharp utility knife for clean edges.

Refinishing the Antique Door

The final stage of restoration involves sanding and applying a new finish to protect and beautify the door.

Sanding Techniques

You can’t rush sanding—here’s how to do it right:

1. Start with medium-grit sandpaper to smooth the entire surface.
2. Progress to finer grits for a polished, pristine finish.
3. Use a sanding block for flat surfaces and hand-sand intricate details to maintain their definition.

Apply the Finish

Silva recommends using a polyurethane finish for its durability and ease of application:

1. Apply a sanding sealer and let it dry for an hour to ensure proper adhesion.
2. Sand lightly with 220-grit paper and wipe clean to remove dust.
3. Apply the first coat of polyurethane with a soft brush, following the wood grain for even coverage.
4. Allow to dry for 24 hours, then lightly sand and apply a second coat to build the finish.
5. Repeat for a third coat if desired for added protection and luster.

Reinstalling Hardware and Hanging the Antique Door

With the finish dry, it’s time to reassemble and rehang the door carefully.

1. Install new or restored hardware that complements the door’s style.
2. Carefully rehang the door on its hinges, ensuring proper alignment.
3. Test the door’s operation and make any necessary adjustments to achieve smooth functionality.

In his project, Silva installs new hardware that enhances the door’s restored appearance, blending modern convenience with antique charm.

Additional Considerations for Antique Door Restoration

Beyond the basic processes, consider any additional customizations or repairs that can further revitalize your antique door. This could include updating decorative elements, reinforcing structural integrity, or adding weatherproofing features for enhanced functionality.

Resources

To restore the original 1918 front door, Silva used a variety of tools and techniques. To strip the trim detail of its old finish, he applied paint and varnish stripper by Max Strip. The stripper is eco-friendly and low-VOC, which makes it safer to use indoors than a traditional paint stripper. The brass scrub brushes used to actually remove the finish can be found at any home center.

To repair the door and smooth out imperfections, Silva applied a few coats of Bondo Wood Filler, which is manufactured by 3M. He then sanded the door smooth using a random orbital sander ETS EC 150/5 EQ-Plus, which is manufactured by Festool.

To resurface the door, he applied a sheet of khaya mahogany peel-and-stick veneer from Boulter Plywood. The veneer can be cut with a utility knife and applied evenly using a roller, which can be found at any home center.

Silva replaced the old hardware with a full mortise Harrison entryset with a Providence knob in an oil-rubbed bronze finish, which was provided by Emtek. The tools required to replace the hardware, including the screwdriver and chisel, can be found at home centers.

Materials

• Paint stripper
• Wood filler
• Epoxy glue
• Plastic wrapping
• Peel-and-stick veneer
• Sanding sealer
• Exterior window sealant
• Hardware
• Polyurethane finish

Tools