Project details
Skill
Cost
Estimated Time
*Cost information in this article sourced from Angi.
Crown molding can transform the look of your kitchen cabinets, adding a touch of elegance and sophistication. While the process may seem daunting, with the right tools and techniques, you can achieve professional-looking results.
This Old House expert, Tom Silva, demonstrates the step-by-step process of installing crown molding on kitchen cabinets, providing valuable insights for homeowners looking to enhance their kitchen’s aesthetic appeal.
Understanding Crown Molding Installation
Crown molding is typically installed at an angle, connecting the top of the cabinet to the ceiling. However, your cabinet type will affect the installation method.
Types of Cabinet Doors
The type of cabinet doors you have will influence how you install crown molding. Understanding these differences can help you avoid common pitfalls and ensure a seamless installation.
- Full overlay doors: These completely cover the cabinet frame, providing a sleek, modern look.
- Inset doors: These sit flush with the cabinet frame, requiring a different approach for crown molding installation.
- Overlay doors: These cover the cabinet frame partially or fully, allowing for a more straightforward crown molding installation.
Preparing for Installation
Here are the essential steps to follow when preparing for your crown molding project:
- Measure your cabinets accurately
- Select appropriate crown molding
- Gather the necessary tools and materials
- Plan your cuts and installation strategy
In the video, Silva emphasizes the importance of careful measurement and planning before cutting. Following these preparatory steps will help you avoid mistakes and ensure a professional finish.
Cabinets With Inset Doors
If your cabinets have inset doors, open them, position the augmented crown on the ceiling, and clamp it to the cabinet’s face frame. Trace a pencil line on the ceiling where it meets the scribe strip, then reclamp the crown so it sits flush with the bottom edge of the face-frame top rail. Draw tick marks across this joint to help you align the crown after scribing.
Set your compass legs to match the widest gap between the crown and ceiling to make the scribe line. Keep the legs aligned vertically as you run the compass point along the line on the ceiling and the pencil along the scribe strip. The pencil line will show the ceiling contour.
On cabinets with overlay doors, which have hidden face frames or no frames at all, you’ll have to mount rabbeted filler pieces to the cabinets’ tops to give you something to nail the crown to.
The fillers above the doors should sit flush with the door faces; these fillers are held in place with screws driven through the tops of the cabinets. The side fillers sit inside the cabinet frame, flush with the sides. They’re fastened to the cabinet with a combination of superglue gel, wood glue, and pin nails.
Steps for hanging crown molding:
- Cut strips of the 5/4-inch pine to length and width based on the size of the cabinets. These will be the filler pieces.
- Make rabbet cuts on the filler pieces so that the piece fits tightly on the top of the cabinet and over the door of the cabinet.
- Once the cuts are all made, spray paint the filler pieces to match the color of the cabinets in case they show through.
- Mount the filler pieces to the cabinets using super glue to hold them in place and wood glue to bond them more permanently.
- From the sides of the cabinet, nail the filler pieces in the place. For the front filler piece, drill from underneath the inside of the cabinet and then secure that piece with wood screws.
- Hold up the crown molding on the sides of the cabinet. Be sure the pieces are tight against the wall. Use a pencil to mark from the inside the correct measurement to cut the crown molding. Draw an arrow on the interior to help determine which angle the miter cut should go.
- Hold the crown molding upside down and backward so that it presses up safely against the fence of the miter saw. To keep it from slipping, you can use some of the clear polyurethane glue and a couple of small pieces of wood to glue on the base of the saw to act as stops.
- Turn the miter saw to 45 degrees based on the direction of the mark drawn on the crown molding during measuring. Cut the piece.
- To make the sister cut on the opposite piece of crown molding, turn the saw to the opposite 45-degree angle and cut it again.
- Nail the two pieces together using the brad nailer and then hold the crown molding back up to the cabinet to get the next measurement. Measure and mark the front piece of crown molding. Be sure to also mark the direction of the angle for the crown molding like before.
- Make the miter cut for the front piece of crown molding. Then, make the sister cut for the following side like before.
- Mount the crown molding to the cabinet using the brad nailer. Repeat this process with the rest of the cabinets with outside corners.
- For any cabinets with an inside corner, cut the miters with the opposite 45-degree angle so that the miter angles on the crown molding cut into itself.
- Fill in all the nail holes with wood putty.
- Caulk around the crown molding where it meets the ceiling to give it a finished look.
Tips for Successful Crown Molding Installation
Installing crown molding on kitchen cabinets can be a complex task, but the following tips can make the job easier:
- Label your pieces: Mark and label each piece to keep track of their positions and ensure accurate installation.
- Practice on scrap pieces: Before making final cuts, practice on scrap pieces to get a feel for the angles and measurements.
- Take your time: Rushing through the installation can lead to mistakes. Take your time measuring, cutting, and fitting each piece carefully.
- Use a high-quality miter saw: A precise miter saw ensures accurate cuts, which are crucial for a seamless fit.
Our Conclusion
While it requires careful planning and precise cuts, installing new crown molding is manageable for many DIY enthusiasts. By following the expert techniques demonstrated by Silva, you can achieve professional-looking results and add lasting value to your home.
Shopping List
- 5/4-inch pine
- Brad nails
- Fast-drying spray primer
- Paintable caulking
- Pencil
- Super glue
- Wood glue
- Wood putty
- Wood screws
