Cisco Systems, Inc

Building D 45 Allee des Ormes - BP1200 Mougins - Sophia Antipolis 06254 France +33 497 23 26 34 [email protected]

Internet Area 6TiSCH deterministic wireless radio mesh This document describes a network architecture that provides low-latency, low-jitter, and high-reliability packet delivery. It combines a high-speed powered backbone and subnetworks using IEEE 802.15.4 time-slotted channel hopping (TSCH) to meet the requirements of low-power wireless deterministic applications.

Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are candidates for any level of Internet Standard; see Section 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at .

Copyright Notice Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents () in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

Table of Contents

• .  Introduction
• .  Terminology
  • .  New Terms
  • .  Abbreviations
  • .  Related Documents
• .  High-Level Architecture
  • .  A Non-broadcast Multi-access Radio Mesh Network
  • .  A Multi-Link Subnet Model
  • .  TSCH: a Deterministic MAC Layer
  • .  Scheduling TSCH
  • .  Distributed vs. Centralized Routing
  • .  Forwarding over TSCH
  • .  6TiSCH Stack
  • .  Communication Paradigms and Interaction Models
• .  Architecture Components
  • .  6LoWPAN (and RPL)
    • .  RPL-Unaware Leaves and 6LoWPAN ND
    • .  6LBR and RPL Root
  • .  Network Access and Addressing
    • .  Join Process
    • .  Registration
  • .  TSCH and 6top
    • .  6top
    • .  Scheduling Functions and the 6top Protocol
    • .  6top and RPL Objective Function Operations
    • .  Network Synchronization
    • .  Slotframes and CDU Matrix
    • .  Distributing the Reservation of Cells
  • .  Schedule Management Mechanisms
    • .  Static Scheduling
    • .  Neighbor-to-Neighbor Scheduling
    • .  Remote Monitoring and Schedule Management
    • .  Hop-by-Hop Scheduling
  • .  On Tracks
    • .  General Behavior of Tracks
    • .  Serial Track
    • .  Complex Track with Replication and Elimination
    • .  DetNet End-to-End Path
    • .  Cell Reuse
  • .  Forwarding Models
    • .  Track Forwarding
    • .  IPv6 Forwarding
    • .  Fragment Forwarding
  • .  Advanced 6TiSCH Routing
    • .  Packet Marking and Handling
    • .  Replication, Retries, and Elimination
• .  IANA Considerations
• .  Security Considerations
  • .  Availability of Remote Services
  • .  Selective Jamming
  • .  MAC-Layer Security
  • .  Time Synchronization
  • .  Validating ASN
  • .  Network Keying and Rekeying
• .  References
  • .  Normative References
  • .  Informative References
• .  Related Work in Progress
  • .  Unchartered IETF Work Items
    • .  6TiSCH Zero-Touch Security
    • .  6TiSCH Track Setup
    • .  Using BIER in a 6TiSCH Network
  • .  External (Non-IETF) Work Items
• Acknowledgments
• Contributors
• Author's Address

Introduction Wireless networks enable a wide variety of devices of any size to get interconnected, often at a very low marginal cost per device, at any range, and in circumstances where wiring may be impractical, for instance, on fast-moving or rotating devices. On the other hand, Deterministic Networking maximizes the packet delivery ratio within a bounded latency so as to enable mission-critical machine-to-machine (M2M) operations. Applications that need such networks are presented in and , which presents a number of additional use cases for Reliable and Available Wireless networks (RAW). The considered applications include professional media, Industrial Automation and Control Systems (IACS), building automation, in-vehicle command and control, commercial automation and asset tracking with mobile scenarios, as well as gaming, drones and edge robotic control, and home automation applications. The Time-Slotted Channel Hopping (TSCH) mode of the IEEE Std 802.15.4 Medium Access Control (MAC) was introduced with the IEEE Std 802.15.4e amendment and is now retrofitted in the main standard. For all practical purposes, this document is expected to be insensitive to the revisions of that standard, which is thus referenced without a date. TSCH is both a Time-Division Multiplexing (TDM) and a Frequency-Division Multiplexing (FDM) technique, whereby a different channel can be used for each transmission. TSCH allows the scheduling of transmissions for deterministic operations and applies to the slower and most energy-constrained wireless use cases. The scheduled operation provides for a more reliable experience, which can be used to monitor and manage resources, e.g., energy and water, in a more efficient fashion. Proven deterministic networking standards for use in process control, including ISA100.11a and WirelessHART , have demonstrated the capabilities of the IEEE Std 802.15.4 TSCH MAC for high reliability against interference, low-power consumption on well-known flows, and its applicability for Traffic Engineering (TE) from a central controller. To enable the convergence of information technology (IT) and operational technology (OT) in Low-Power and Lossy Networks (LLNs), the 6TiSCH architecture supports an IETF suite of protocols over the IEEE Std 802.15.4 TSCH MAC to provide IP connectivity for energy and otherwise constrained wireless devices. The 6TiSCH architecture relies on IPv6 and the use of routing to provide large scaling capabilities. The addition of a high-speed federating backbone adds yet another degree of scalability to the design. The backbone is typically a Layer 2 transit link such as an Ethernet bridged network, but it can also be a more complex routed structure. The 6TiSCH architecture introduces an IPv6 multi-link subnet model that is composed of a federating backbone and a number of IEEE Std 802.15.4 TSCH low-power wireless networks federated and synchronized by Backbone Routers. If the backbone is a Layer 2 transit link, then the Backbone Routers can operate as an IPv6 Neighbor Discovery (IPv6 ND) proxy . The 6TiSCH architecture leverages 6LoWPAN to adapt IPv6 to the constrained media and the Routing Protocol for Low-Power and Lossy Networks (RPL) for the distributed routing operations. Centralized routing refers to a model where routes are computed and resources are allocated from a central controller. This is particularly helpful to schedule deterministic multihop transmissions. In contrast, distributed routing refers to a model that relies on concurrent peer-to-peer protocol exchanges for TSCH resource allocation and routing operations. The architecture defines mechanisms to establish and maintain routing and scheduling in a centralized, distributed, or mixed fashion, for use in multiple OT environments. It is applicable in particular to highly scalable solutions such as those used in Advanced Metering Infrastructure solutions that leverage distributed routing to enable multipath forwarding over large LLN meshes.

Terminology

New Terms The document does not reuse terms from the IEEE Std 802.15.4 standard such as "path" or "link", which bear a meaning that is quite different from classical IETF parlance. This document adds the following terms:

6TiSCH (IPv6 over the TSCH mode of IEEE 802.15.4):

6TiSCH defines an adaptation sublayer for IPv6 over TSCH called 6top, a set of protocols for setting up a TSCH schedule in distributed approach, and a security solution. 6TiSCH may be extended in the future for other MAC/Physical Layer (PHY) pairs providing a service similar to TSCH.

6top (6TiSCH Operation Sublayer):

The next higher layer of the IEEE Std 802.15.4 TSCH MAC layer. 6top provides the abstraction of an IP link over a TSCH MAC, schedules packets over TSCH cells, and exposes a management interface to schedule TSCH cells.

6P (6top Protocol):

The protocol defined in . 6P enables Layer 2 peers to allocate, move, or de-allocate cells in their respective schedules to communicate. 6P operates at the 6top sublayer.

6P transaction:

A 2-way or 3-way sequence of 6P messages used by Layer 2 peers to modify their communication schedule.

ASN (Absolute Slot Number):

Defined in , the ASN is the total number of timeslots that have elapsed since the Epoch time when the TSCH network started. Incremented by one at each timeslot. It is wide enough to not roll over in practice.

bundle:

A group of equivalent scheduled cells, i.e., cells identified by different slotOffset/channelOffset, which are scheduled for a same purpose, with the same neighbor, with the same flags, and the same slotframe. The size of the bundle refers to the number of cells it contains. For a given slotframe length, the size of the bundle translates directly into bandwidth. A bundle is a local abstraction that represents a half-duplex link for either sending or receiving, with bandwidth that amounts to the sum of the cells in the bundle.

Layer 2 vs. Layer 3 bundle:

Bundles are associated with either Layer 2 (switching) or Layer 3 (routing) forwarding operations. A pair of Layer 3 bundles (one for each direction) maps to an IP link with a neighbor, whereas a set of Layer 2 bundles (of an "arbitrary" cardinality and direction) corresponds to the relation of one or more incoming bundle(s) from the previous-hop neighbor(s) with one or more outgoing bundle(s) to the next-hop neighbor(s) along a Track as part of the switching role, which may include replication and elimination.

CCA (Clear Channel Assessment):

A mechanism defined in whereby nodes listen to the channel before sending to detect ongoing transmissions from other parties. Because the network is synchronized, CCA cannot be used to detect colliding transmissions within the same network, but it can be used to detect other radio networks in the vicinity.

cell:

A unit of transmission resource in the CDU matrix, a cell is identified by a slotOffset and a channelOffset. A cell can be scheduled or unscheduled.

Channel Distribution/Usage (CDU) matrix:

: A matrix of cells (i,j) representing the spectrum (channel) distribution among the different nodes in the 6TiSCH network. The CDU matrix has width in timeslots equal to the period of the network scheduling operation, and height equal to the number of available channels. Every cell (i,j) in the CDU, identified by slotOffset/channelOffset, belongs to a specific chunk.

channelOffset:

Identifies a row in the TSCH schedule. The number of channelOffset values is bounded by the number of available frequencies. The channelOffset translates into a frequency with a function that depends on the absolute time when the communication takes place, resulting in a channel-hopping operation.

chunk:

A well-known list of cells, distributed in time and frequency, within a CDU matrix. A chunk represents a portion of a CDU matrix. The partition of the CDU matrix in chunks is globally known by all the nodes in the network to support the appropriation process, which is a negotiation between nodes within an interference domain. A node that manages to appropriate a chunk gets to decide which transmissions will occur over the cells in the chunk within its interference domain, i.e., a parent node will decide when the cells within the appropriated chunk are used and by which node among its children.

CoJP (Constrained Join Protocol):

The Constrained Join Protocol (CoJP) enables a pledge to securely join a 6TiSCH network and obtain network parameters over a secure channel. "" defines the minimal CoJP setup with pre-shared keys defined. In that mode, CoJP can operate with a single round-trip exchange.

dedicated cell:

A cell that is reserved for a given node to transmit to a specific neighbor.

deterministic network:

The generic concept of a deterministic network is defined in the "Deterministic Networking Architecture" document. When applied to 6TiSCH, it refers to the reservation of Tracks, which guarantees an end-to-end latency and optimizes the Packet Delivery Ratio (PDR) for well-characterized flows.

distributed cell reservation:

A reservation of a cell done by one or more in-network entities.

distributed Track reservation:

A reservation of a Track done by one or more in-network entities.

EB (Enhanced Beacon):

A special frame defined in used by a node, including the Join Proxy (JP), to announce the presence of the network. It contains enough information for a pledge to synchronize to the network.

hard cell:

A scheduled cell that the 6top sublayer may not relocate.

hopping sequence:

Ordered sequence of frequencies, identified by a Hopping_Sequence_ID, used for channel hopping when translating the channelOffset value into a frequency.

IE (Information Element):

Type-Length-Value containers placed at the end of the MAC header and used to pass data between layers or devices. Some IE identifiers are managed by the IEEE . Some IE identifiers are managed by the IETF . uses one subtype to support the selection of the Join Proxy.

join process:

The overall process that includes the discovery of the network by pledge(s) and the execution of the join protocol.

join protocol:

The protocol that allows the pledge to join the network. The join protocol encompasses authentication, authorization, and parameter distribution. The join protocol is executed between the pledge and the JRC.

joined node:

The new device after having completed the join process, often just called a node.

JP (Join Proxy):

A node already part of the 6TiSCH network that serves as a relay to provide connectivity between the pledge and the JRC. The JP announces the presence of the network by regularly sending EB frames.

JRC (Join Registrar/Coordinator):

Central entity responsible for the authentication, authorization, and configuration of the pledge.

link:

A communication facility or medium over which nodes can communicate at the link layer, which is the layer immediately below IP. In 6TiSCH, the concept is implemented as a collection of Layer 3 bundles. Note: the IETF parlance for the term "link" is adopted, as opposed to the IEEE Std 802.15.4 terminology.

operational technology:

OT refers to technology used in automation, for instance in industrial control networks. The convergence of IT and OT is the main object of the Industrial Internet of Things (IIOT).

pledge:

A new device that attempts to join a 6TiSCH network.

(to) relocate a cell:

The action operated by the 6top sublayer of changing the slotOffset and/or channelOffset of a soft cell.

(to) schedule a cell:

The action of turning an unscheduled cell into a scheduled cell.

scheduled cell:

A cell that is assigned a neighbor MAC address (broadcast address is also possible) and one or more of the following flags: TX, RX, Shared, and Timekeeping. A scheduled cell can be used by the IEEE Std 802.15.4 TSCH implementation to communicate. A scheduled cell can either be a hard or a soft cell.

SF (6top Scheduling Function):

The cell management entity that adds or deletes cells dynamically based on application networking requirements. The cell negotiation with a neighbor is done using 6P.

SFID (6top Scheduling Function Identifier):

A 4-bit field identifying an SF.

shared cell:

A cell marked with both the TX and Shared flags. This cell can be used by more than one transmitter node. A back-off algorithm is used to resolve contention.

slotframe:

A collection of timeslots repeating in time, analogous to a superframe in that it defines periods of communication opportunities. It is characterized by a slotframe_ID and a slotframe_size. Multiple slotframes can coexist in a node's schedule, i.e., a node can have multiple activities scheduled in different slotframes based on the priority of its packets/traffic flows. The timeslots in the slotframe are indexed by the slotOffset; the first timeslot is at slotOffset 0.

slotOffset:

A column in the TSCH schedule, i.e., the number of timeslots since the beginning of the current iteration of the slotframe.

soft cell:

A scheduled cell that the 6top sublayer can relocate.

time source neighbor:

A neighbor that a node uses as its time reference, and to which it needs to keep its clock synchronized.

timeslot:

A basic communication unit in TSCH that allows a transmitter node to send a frame to a receiver neighbor and that allows the receiver neighbor to optionally send back an acknowledgment.

Track:

A Track is a Directed Acyclic Graph (DAG) that is used as a complex multihop path to the destination(s) of the path. In the case of unicast traffic, the Track is a Destination-Oriented DAG (DODAG) where the Root of the DODAG is the destination of the unicast traffic. A Track enables replication, elimination, and reordering functions on the way (more on those functions in ). A Track reservation locks physical resources such as cells and buffers in every node along the DODAG. A Track is associated with an owner, which can be for instance the destination of the Track.

TrackID:

A TrackID is either globally unique or locally unique to the Track owner, in which case the identification of the owner must be provided together with the TrackID to provide a full reference to the Track. Typically, the Track owner is the ingress of the Track, the IPv6 source address of packets along the Track can be used as identification of the owner, and a local InstanceID in the namespace of that owner can be used as TrackID. If the Track is reversible, then the owner is found in the IPv6 destination address of a packet coming back along the Track. In that case, a RPL Packet Information in an IPv6 packet can unambiguously identify the Track and can be expressed in a compressed form using .

TSCH:

A medium access mode of the IEEE Std 802.15.4 standard that uses time synchronization to achieve ultra-low-power operation and channel hopping to enable high reliability.

TSCH Schedule:

A matrix of cells, with each cell indexed by a slotOffset and a channelOffset. The TSCH schedule contains all the scheduled cells from all slotframes and is sufficient to qualify the communication in the TSCH network. The number of channelOffset values (the "height" of the matrix) is equal to the number of available frequencies.

Unscheduled Cell:

A cell that is not used by the IEEE Std 802.15.4 TSCH implementation.

Abbreviations This document uses the following abbreviations:

6BBR:

6LoWPAN Backbone Router (router with a proxy ND function)

6LBR:

6LoWPAN Border Router (authoritative on Duplicate Address Detection (DAD))

6LN:

6LoWPAN Node

6LR:

6LoWPAN Router (relay to the registration process)

6CIO:

Capability Indication Option

(E)ARO:

(Extended) Address Registration Option

(E)DAR:

(Extended) Duplicate Address Request

(E)DAC:

(Extended) Duplicate Address Confirmation

DAD:

Duplicate Address Detection

DODAG:

Destination-Oriented Directed Acyclic Graph

LLN:

Low-Power and Lossy Network (a typical IoT network)

NA:

Neighbor Advertisement

NCE:

Neighbor Cache Entry

ND:

Neighbor Discovery

NDP:

Neighbor Discovery Protocol

PCE:

Path Computation Element

NME:

Network Management Entity

ROVR:

Registration Ownership Verifier (pronounced rover)

RPL:

IPv6 Routing Protocol for LLNs (pronounced ripple)

RA:

Router Advertisement

RS:

Router Solicitation

TSCH:

Time-Slotted Channel Hopping

TID:

Transaction ID (a sequence counter in the EARO)

Related Documents The document conforms to the terms and models described in and , uses the vocabulary and the concepts defined in for the IPv6 architecture, and refers to for reservation. The document uses domain-specific terminology defined or referenced in the following:

• 6LoWPAN ND: "Neighbor Discovery Optimization for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)" and "Registration Extensions for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery",
• "Terms Used in Routing for Low-Power and Lossy Networks", and
• RPL: "Objective Function Zero for the Routing Protocol for Low-Power and Lossy Networks (RPL)" and "RPL: IPv6 Routing Protocol for Low-Power and Lossy Networks".

Other terms in use in LLNs are found in "Terminology for Constrained-Node Networks". Readers are expected to be familiar with all the terms and concepts that are discussed in the following:

• "Neighbor Discovery for IP version 6 (IPv6)" and
• "IPv6 Stateless Address Autoconfiguration".

In addition, readers would benefit from reading the following prior to this specification for a clear understanding of the art in ND-proxying and binding:

• "Problem Statement and Requirements for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Routing",
• "Multi-Link Subnet Issues", and
• "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals".

High-Level Architecture

A Non-broadcast Multi-access Radio Mesh Network A 6TiSCH network is an IPv6 subnet that, in its basic configuration illustrated in , is a single Low-Power and Lossy Network (LLN) operating over a synchronized TSCH-based mesh.

Basic Configuration of a 6TiSCH Network ---+-------- ............ ------------ | External Network | | +-----+ +-----+ | NME | | | LLN Border | PCE | | | router (6LBR) +-----+ +-----+ o o o o o o o o o o 6LoWPAN + RPL o o o o o o

Inside a 6TiSCH LLN, nodes rely on 6LoWPAN header compression (6LoWPAN HC) to encode IPv6 packets. From the perspective of the network layer, a single LLN interface (typically an IEEE Std 802.15.4-compliant radio) may be seen as a collection of links with different capabilities for unicast or multicast services. 6TiSCH nodes join a mesh network by attaching to nodes that are already members of the mesh (see ). The security aspects of the join process are further detailed in . In a mesh network, 6TiSCH nodes are not necessarily reachable from one another at Layer 2, and an LLN may span over multiple links. This forms a homogeneous non-broadcast multi-access (NBMA) subnet, which is beyond the scope of IPv6 Neighbor Discovery (IPv6 ND) . 6LoWPAN Neighbor Discovery (6LoWPAN ND) specifies extensions to IPv6 ND that enable ND operations in this type of subnet that can be protected against address theft and impersonation with . Once it has joined the 6TiSCH network, a node acquires IPv6 addresses and registers them using 6LoWPAN ND. This guarantees that the addresses are unique and protects the address ownership over the subnet, more in . Within the NBMA subnet, RPL enables routing in the so-called "route-over" fashion, either in storing (stateful) or non-storing (stateless, with routing headers) mode. From there, some nodes can act as routers for 6LoWPAN ND and RPL operations, as detailed in . With TSCH, devices are time synchronized at the MAC level. The use of a particular RPL Instance for time synchronization is discussed in . With this mechanism, the time synchronization starts at the RPL Root and follows the RPL loopless routing topology. RPL forms Destination-Oriented Directed Acyclic Graphs (DODAGs) within Instances of the protocol, each Instance being associated with an Objective Function (OF) to form a routing topology. A particular 6TiSCH node, the LLN Border Router (6LBR), acts as RPL Root, 6LoWPAN HC terminator, and Border Router for the LLN to the outside. The 6LBR is usually powered. More on RPL Instances can be found in Section of RPL, in particular " RPL Identifiers" and " Instances, DODAGs, and DODAG Versions". RPL adds artifacts in the data packets that are compressed with a 6LoWPAN Routing Header (6LoRH). In a preexisting network, the compression can be globally turned on in a DODAG once all nodes are migrated to support using . Additional routing and scheduling protocols may be deployed to establish on-demand, peer-to-peer routes with particular characteristics inside the 6TiSCH network. This may be achieved in a centralized fashion by a Path Computation Element (PCE) that programs both the routes and the schedules inside the 6TiSCH nodes or in a distributed fashion by using a reactive routing protocol and a hop-by-hop scheduling protocol. This architecture expects that a 6LoWPAN node can connect as a leaf to a RPL network, where the leaf support is the minimal functionality to connect as a host to a RPL network without the need to participate in the full routing protocol. The architecture also expects that a 6LoWPAN node that is unaware of RPL may also connect as described in .

A Multi-Link Subnet Model An extended configuration of the subnet comprises multiple LLNs as illustrated in . In the extended configuration, a Routing Registrar may be connected to the node that acts as the RPL Root and/or 6LoWPAN 6LBR and provides connectivity to the larger campus or factory plant network over a high-speed backbone or a back-haul link. The Routing Registrar may perform IPv6 ND proxy operations; redistribute the registration in a routing protocol such as OSPF or BGP; or inject a route in a mobility protocol such as Mobile IPv6 (MIPv6), Network Mobility (NEMO), or Locator/ID Separation Protocol (LISP). Multiple LLNs can be interconnected and possibly synchronized over a backbone, which can be wired or wireless. The backbone can operate with IPv6 ND procedures or a hybrid of IPv6 ND and 6LoWPAN ND .

Extended Configuration of a 6TiSCH Network | +-----+ +-----+ +-----+ (default) | | (Optional) | | | | IPv6 Router | | 6LBR | | | | Node +-----+ +-----+ +-----+ | Backbone side | | --------+---+--------------------+-+---------------+------+--- | | | +-----------+ +-----------+ +-----------+ | Routing | | Routing | | Routing | | Registrar | | Registrar | | Registrar | +-----------+ +-----------+ +-----------+ o Wireless side o o o o o o o o o o o o o o o o o o o 6TiSCH o 6TiSCH o o o o 6TiSCH o o o LLN o o o o LLN o o LLN o o o o o o o o o o o o o o o

A Routing Registrar that performs proxy IPv6 ND operations over the backbone on behalf of the 6TiSCH nodes is called a Backbone Router (6BBR) . The 6BBRs are placed along the wireless edge of a backbone and federate multiple wireless links to form a single multi-link subnet. The 6BBRs synchronize with one another over the backbone, so as to ensure that the multiple LLNs that form the IPv6 subnet stay tightly synchronized. The use of multicast can also be reduced on the backbone with a registrar that would contribute to Duplicate Address Detection as well as address lookup using only unicast request/response exchanges. is a proposed method that presents an example of how this could be achieved with an extension of , using an optional 6LBR as a subnet-level registrar, as illustrated in . As detailed in , the 6LBR that serves the LLN and the Root of the RPL network need to share information about the devices that are learned through either 6LoWPAN ND or RPL, but not both. The preferred way of achieving this is to co-locate or combine them. The combined RPL Root and 6LBR may be co-located with the 6BBR, or directly attached to the 6BBR. In the latter case, it leverages the extended registration process defined in to proxy the 6LoWPAN ND registration to the 6BBR on behalf of the LLN nodes, so that the 6BBR may in turn perform classical ND operations over the backbone as a proxy. The "Deterministic Networking Architecture" studies Layer 3 aspects of Deterministic Networks and covers networks that span multiple Layer 2 domains. If the backbone is deterministic (such as defined by the Time-Sensitive Networking (TSN) Task Group at IEEE), then the Backbone Router ensures that the end-to-end deterministic behavior is maintained between the LLN and the backbone.

TSCH: a Deterministic MAC Layer Though at a different time scale (several orders of magnitude), both IEEE Std 802.1 TSN and IEEE Std 802.15.4 TSCH standards provide deterministic capabilities to the point that a packet pertaining to a certain flow may traverse a network from node to node following a precise schedule, as a train that enters and then leaves intermediate stations at precise times along its path. With TSCH, time is formatted into timeslots, and individual communication cells are allocated to unicast or broadcast communication at the MAC level. The time-slotted operation reduces collisions, saves energy, and enables more closely engineering the network for deterministic properties. The channel-hopping aspect is a simple and efficient technique to combat multipath fading and co-channel interference. 6TiSCH builds on the IEEE Std 802.15.4 TSCH MAC and inherits its advanced capabilities to enable them in multiple environments where they can be leveraged to improve automated operations. The 6TiSCH architecture also inherits the capability to perform a centralized route computation to achieve deterministic properties, though it relies on the IETF DetNet architecture and IETF components such as the PCE for the protocol aspects. On top of this inheritance, 6TiSCH adds capabilities for distributed routing and scheduling operations based on RPL and capabilities for negotiating schedule adjustments between peers. These distributed routing and scheduling operations simplify the deployment of TSCH networks and enable wireless solutions in a larger variety of use cases from operational technology in general. Examples of such use cases in industrial environments include plant setup and decommissioning, as well as monitoring a multiplicity of minor notifications such as corrosion measurements, events, and access of local devices by mobile workers.

Scheduling TSCH A scheduling operation allocates cells in a TDM/FDM matrix called a CDU either to individual transmissions or as multi-access shared resources. The CDU matrix can be formatted in chunks that can be allocated exclusively to particular nodes to enable distributed scheduling without collision. More in . At the MAC layer, the schedule of a 6TiSCH node is the collection of the timeslots at which it must wake up for transmission, and the channels to which it should either send or listen at those times. The schedule is expressed as one or more repeating slotframes. Slotframes may collide and require a device to wake up at a same time, in which case the slotframe with the highest priority is actionable. The 6top sublayer (see for more) hides the complexity of the schedule from the upper layers. The link abstraction that IP traffic utilizes is composed of a pair of Layer 3 cell bundles, one to receive and one to transmit. Some of the cells may be shared, in which case the 6top sublayer must perform some arbitration. Scheduling enables multiple simultaneous communications in a same interference domain using different channels; but a node equipped with a single radio can only either transmit or receive on one channel at any point of time. Scheduled cells that fulfill the same role, e.g., receive IP packets from a peer, are grouped in bundles. The 6TiSCH architecture identifies four ways a schedule can be managed and CDU cells can be allocated: Static Scheduling, Neighbor-to-Neighbor Scheduling, Centralized (or Remote) Monitoring and Schedule Management, and Hop-by-Hop Scheduling.

Static Scheduling:

This refers to the minimal 6TiSCH operation whereby a static schedule is configured for the whole network for use in a Slotted ALOHA fashion. The static schedule is distributed through the native methods in the TSCH MAC layer and does not preclude other scheduling operations coexisting on a same 6TiSCH network. A static schedule is necessary for basic operations such as the join process and for interoperability during the network formation, which is specified as part of the Minimal 6TiSCH Configuration .

Neighbor-to-Neighbor Scheduling:

This refers to the dynamic adaptation of the bandwidth of the links that are used for IPv6 traffic between adjacent peers. Scheduling Functions such as the "6TiSCH Minimal Scheduling Function (MSF)" influence the operation of the MAC layer to add, update, and remove cells in its own and its peer's schedules using 6P for the negotiation of the MAC resources.

Centralized (or Remote) Monitoring and Schedule Management:

This refers to the central computation of a schedule and the capability to forward a frame based on the cell of arrival. In that case, the related portion of the device schedule as well as other device resources are managed by an abstract Network Management Entity (NME), which may cooperate with the PCE to minimize the interaction with, and the load on, the constrained device. This model is the TSCH adaption of the DetNet architecture, and it enables Traffic Engineering with deterministic properties.

Hop-by-Hop Scheduling:

This refers to the possibility of reserving cells along a path for a particular flow using a distributed mechanism.

It is not expected that all use cases will require all those mechanisms. Static Scheduling with minimal configuration is the only one that is expected in all implementations, since it provides a simple and solid basis for convergecast routing and time distribution. A deeper dive into those mechanisms can be found in .

Distributed vs. Centralized Routing 6TiSCH enables a mixed model of centralized routes and distributed routes. Centralized routes can, for example, be computed by an entity such as a PCE. 6TiSCH leverages RPL for interoperable, distributed routing operations. Both methods may inject routes into the routing tables of the 6TiSCH routers. In either case, each route is associated with a 6TiSCH topology that can be a RPL Instance topology or a Track. The 6TiSCH topology is indexed by a RPLInstanceID, in a format that reuses the RPLInstanceID as defined in RPL. RPL is applicable to Static Scheduling and Neighbor-to-Neighbor Scheduling. The architecture also supports a centralized routing model for Remote Monitoring and Schedule Management. It is expected that a routing protocol that is more optimized for point-to-point routing than RPL, such as the "Asymmetric AODV-P2P-RPL in Low-Power and Lossy Networks" (AODV-RPL), which derives from the "Ad Hoc On-demand Distance Vector (AODVv2) Routing", will be selected for Hop-by-Hop Scheduling. Both RPL and PCE rely on shared sources such as policies to define global and local RPLInstanceIDs that can be used by either method. It is possible for centralized and distributed routing to share the same topology. Generally they will operate in different slotframes, and centralized routes will be used for scheduled traffic and will have precedence over distributed routes in case of conflict between the slotframes.

Forwarding over TSCH The 6TiSCH architecture supports three different forwarding models. One is the classical IPv6 Forwarding, where the node selects a feasible successor at Layer 3 on a per-packet basis and based on its routing table. The second derives from Generalized MPLS (GMPLS) for so-called Track Forwarding, whereby a frame received at a particular timeslot can be switched into another timeslot at Layer 2 without regard to the upper-layer protocol. The third model is the 6LoWPAN Fragment Forwarding, which allows the forwarding individual 6LoWPAN fragments along a route that is set up by the first fragment. In more detail:

IPv6 Forwarding:

This is the classical IP forwarding model, with a Routing Information Base (RIB) that is installed by RPL and used to select a feasible successor per packet. The packet is placed on an outgoing link, which the 6top sublayer maps into a (Layer 3) bundle of cells, and scheduled for transmission based on QoS parameters. Besides RPL, this model also applies to any routing protocol that may be operated in the 6TiSCH network and corresponds to all the distributed scheduling models: Static, Neighbor-to-Neighbor, and Hop-by-Hop Scheduling.

GMPLS Track Forwarding:

This model corresponds to the Remote Monitoring and Schedule Management. In this model, a central controller (hosting a PCE) computes and installs the schedules in the devices per flow. The incoming (Layer 2) bundle of cells from the previous node along the path determines the outgoing (Layer 2) bundle towards the next hop for that flow as determined by the PCE. The programmed sequence for bundles is called a Track and can assume DAG shapes that are more complex than a simple direct sequence of nodes.

6LoWPAN Fragment Forwarding:

This is a hybrid model that derives from IPv6 forwarding for the case where packets must be fragmented at the 6LoWPAN sublayer. The first fragment is forwarded like any IPv6 packet and leaves a state in the intermediate hops to enable forwarding of the next fragments that do not have an IP header without the need to recompose the packet at every hop.

A deeper dive into these operations can be found in . summarizes how the forwarding models apply to the various routing and scheduling possibilities:

Forwarding Model	Routing	Scheduling
classical IPv6 / 6LoWPAN Fragment	RPL	Static (Minimal Configuration)
		Neighbor-to-Neighbor (SF+6P)
	Reactive	Hop-by-Hop (AODV-RPL)
GMPLS Track Forwarding	PCE	Remote Monitoring and Schedule Mgt

6TiSCH Stack The IETF proposes multiple techniques for implementing functions related to routing, transport, or security. The 6TiSCH architecture limits the possible variations of the stack and recommends a number of base elements for LLN applications to control the complexity of possible deployments and device interactions and to limit the size of the resulting object code. In particular, UDP , IPv6 , and the Constrained Application Protocol (CoAP) are used as the transport/binding of choice for applications and management as opposed to TCP and HTTP. The resulting protocol stack is represented in :

6TiSCH Protocol Stack +--------+--------+ | Applis | CoJP | +--------+--------+--------------+-----+ | CoAP / OSCORE | 6LoWPAN ND | RPL | +-----------------+--------------+-----+ | UDP | ICMPv6 | +-----------------+--------------------+ | IPv6 | +--------------------------------------+----------------------+ | 6LoWPAN HC / 6LoRH HC | Scheduling Functions | +--------------------------------------+----------------------+ | 6top inc. 6top Protocol | +-------------------------------------------------------------+ | IEEE Std 802.15.4 TSCH | +-------------------------------------------------------------+

RPL is the routing protocol of choice for LLNs. So far, there is no identified need to define a 6TiSCH-specific Objective Function. The Minimal 6TiSCH Configuration describes the operation of RPL over a static schedule used in a Slotted ALOHA fashion , whereby all active slots may be used for emission or reception of both unicast and multicast frames. 6LoWPAN header compression is used to compress the IPv6 and UDP headers, whereas the 6LoWPAN Routing Header (6LoRH) is used to compress the RPL artifacts in the IPv6 data packets, including the RPL Packet Information (RPI), the IP-in-IP encapsulation to/from the RPL Root, and the Source Routing Header (SRH) in non-storing mode. "" provides the details on when headers or encapsulation are needed. The Object Security for Constrained RESTful Environments (OSCORE) is leveraged by the Constrained Join Protocol (CoJP) and is expected to be the primary protocol for the protection of the application payload as well. The application payload may also be protected by the Datagram Transport Layer Security (DTLS) sitting either under CoAP or over CoAP so it can traverse proxies. The 6TiSCH Operation Sublayer (6top) is a sublayer of a Logical Link Control (LLC) that provides the abstraction of an IP link over a TSCH MAC and schedules packets over TSCH cells, as further discussed in the next sections, providing in particular dynamic cell allocation with the 6top Protocol (6P) . The reference stack presented in this document was implemented and interoperability-tested by a combination of open source, IETF, and ETSI efforts. One goal is to help other bodies to adopt the stack as a whole, making the effort to move to an IPv6-based IoT stack easier. For a particular environment, some of the choices that are available in this architecture may not be relevant. For instance, RPL is not required for star topologies and mesh-under Layer 2 routed networks, and the 6LoWPAN compression may not be sufficient for ultra-constrained cases such as some Low-Power Wide Area (LPWA) networks. In such cases, it is perfectly doable to adopt a subset of the selection that is presented hereafter and then select alternate components to complete the solution wherever needed.

Communication Paradigms and Interaction Models provides the terms of Communication Paradigms and Interaction Models in combination with "On the Difference between Information Models and Data Models". A Communication Paradigm is an abstract view of a protocol exchange and has an Information Model for the information that is being exchanged. In contrast, an Interaction Model is more refined and points to standard operation such as a Representational State Transfer (REST) "GET" operation and matches a Data Model for the data that is provided over the protocol exchange. and its following sections discuss application-layer paradigms such as source-sink, which is a multipeer-to-multipeer model primarily used for alarms and alerts, publish-subscribe, which is typically used for sensor data, as well as peer-to-peer and peer-to-multipeer communications. Additional considerations on duocast -- one sender, two receivers for redundancy -- and its N-cast generalization are also provided. Those paradigms are frequently used in industrial automation, which is a major use case for IEEE Std 802.15.4 TSCH wireless networks with and , which provides a wireless access to applications and devices. This document focuses on Communication Paradigms and Interaction Models for packet forwarding and TSCH resources (cells) management. Management mechanisms for the TSCH schedule at the link layer (one hop), network layer (multihop along a Track), and application layer (remote control) are discussed in . Link-layer frame forwarding interactions are discussed in , and network-layer packet routing is addressed in .

Architecture Components

6LoWPAN (and RPL) A RPL DODAG is formed of a Root, a collection of routers, and leaves that are hosts. Hosts are nodes that do not forward packets that they did not generate. RPL-aware leaves will participate in RPL to advertise their own addresses, whereas RPL-unaware leaves depend on a connected RPL router to do so. RPL interacts with 6LoWPAN ND at multiple levels, in particular at the Root and in the RPL-unaware leaves.

RPL-Unaware Leaves and 6LoWPAN ND RPL needs a set of information to advertise a leaf node through a Destination Advertisement Object (DAO) message and establish reachability. "Routing for RPL Leaves" details the basic interaction of 6LoWPAN ND and RPL and enables a plain 6LN that supports to obtain return connectivity via the RPL network as a RPL-unaware leaf. The leaf indicates that it requires reachability services for the Registered Address from a Routing Registrar by setting an 'R' flag in the Extended Address Registration Option , and it provides a TID that maps to the "Path Sequence" defined in , and its operation is defined in . also enables the leaf to signal with the RPLInstanceID that it wants to participate by using the Opaque field of the EARO. On the backbone, the RPLInstanceID is expected to be mapped to an overlay that matches the RPL Instance, e.g., a Virtual LAN (VLAN) or a virtual routing and forwarding (VRF) instance. Though, at the time of this writing, the above specification enables a model where the separation is possible, this architecture recommends co-locating the functions of 6LBR and RPL Root.

6LBR and RPL Root With the 6LoWPAN ND , information on the 6LBR is disseminated via an Authoritative Border Router Option (ABRO) in RA messages. extends to enable a registration for routing and proxy ND. The capability to support is indicated in the 6LoWPAN Capability Indication Option (6CIO). The discovery and liveliness of the RPL Root are obtained through RPL itself. When 6LoWPAN ND is coupled with RPL, the 6LBR and RPL Root functionalities are co-located in order that the address of the 6LBR is indicated by RPL DODAG Information Object (DIO) messages and to associate the ROVR from the Extended Duplicate Address Request/Confirmation (EDAR/EDAC) exchange with the state that is maintained by RPL. specifies how the DAO messages are used to reconfirm the registration, thus eliminating a duplication of functionality between DAO and EDAR/EDAC messages, as illustrated in . also provides the protocol elements that are needed when the 6LBR and RPL Root functionalities are not co-located. Even though the Root of the RPL network is integrated with the 6LBR, it is logically separated from the Backbone Router (6BBR) that is used to connect the 6TiSCH LLN to the backbone. This way, the Root has all information from 6LoWPAN ND and RPL about the LLN devices attached to it. This architecture also expects that the Root of the RPL network (proxy-)registers the 6TiSCH nodes on their behalf to the 6BBR, for whatever operation the 6BBR performs on the backbone, such as ND proxy or redistribution in a routing protocol. This relies on an extension of the 6LoWPAN ND registration described in . This model supports the movement of a 6TiSCH device across the multi-link subnet and allows the proxy registration of 6TiSCH nodes deep into the 6TiSCH LLN by the 6LBR / RPL Root. This is why in the Registered Address is signaled in the Target Address field of the Neighbor Solicitation (NS) message as opposed to the IPv6 Source Address, which, in the case of a proxy registration, is that of the 6LBR / RPL Root itself.

Network Access and Addressing

Join Process A new device, called the pledge, undergoes the join protocol to become a node in a 6TiSCH network. This usually occurs only once when the device is first powered on. The pledge communicates with the Join Registrar/Coordinator (JRC) of the network through a Join Proxy (JP), a radio neighbor of the pledge. The JP is discovered though MAC-layer beacons. When multiple JPs from possibly multiple networks are visible, using trial and error until an acceptable position in the right network is obtained becomes inefficient. adds a new subtype in the Information Element that was delegated to the IETF and provides visibility into the network that can be joined and the willingness of the JP and the Root to be used by the pledge. The join protocol provides the following functionality:

• Mutual authentication
• Authorization
• Parameter distribution to the pledge over a secure channel

The Minimal Security Framework for 6TiSCH defines the minimal mechanisms required for this join process to occur in a secure manner. The specification defines the Constrained Join Protocol (CoJP), which is used to distribute the parameters to the pledge over a secure session established through OSCORE and which describes the secure configuration of the network stack. In the minimal setting with pre-shared keys (PSKs), CoJP allows the pledge to join after a single round-trip exchange with the JRC. The provisioning of the PSK to the pledge and the JRC needs to be done out of band, through a 'one-touch' bootstrapping process, which effectively enrolls the pledge into the domain managed by the JRC. In certain use cases, the 'one-touch' bootstrapping is not feasible due to the operational constraints, and the enrollment of the pledge into the domain needs to occur in-band. This is handled through a 'zero-touch' extension of the Minimal Security Framework for 6TiSCH. The zero-touch extension leverages the "" work to establish a shared secret between a pledge and the JRC without necessarily having them belong to a common (security) domain at join time. This happens through inter-domain communication occurring between the JRC of the network and the domain of the pledge, represented by a fourth entity, Manufacturer Authorized Signing Authority (MASA). Once the zero-touch exchange completes, the CoJP exchange defined in is carried over the secure session established between the pledge and the JRC. depicts the join process and where a Link-Local Address (LLA) is used, versus a Global Unicast Address (GUA).

Join Process in a Multi-Link Subnet. Parentheses () denote optional exchanges. 6LoWPAN Node 6LR 6LBR Join Registrar MASA (pledge) (Join Proxy) (Root) /Coordinator (JRC) | | | | | | 6LoWPAN ND |6LoWPAN ND+RPL | IPv6 network |IPv6 network | | LLN link |Route-Over mesh|(the Internet)|(the Internet)| | | | | | | Layer 2 | | | | |Enhanced Beacon| | | | |<--------------| | | | | | | | | | NS (EARO) | | | | | (for the LLA) | | | | |-------------->| | | | | NA (EARO) | | | | |<--------------| | | | | | | | | | (Zero-touch | | | | | handshake) | (Zero-touch handshake) | (Zero-touch | | using LLA | using GUA | handshake) | |<------------->|<---------------------------->|<------------>| | | | | | | CoJP Join Req | | | | \ | using LLA | | | | | |-------------->| | | | | | | CoJP Join Request | | | | | using GUA | | | | |----------------------------->| | | C | | | | | | o | | CoJP Join Response | | | J | | using GUA | | | P | |<-----------------------------| | | |CoJP Join Resp | | | | | | using LLA | | | | | |<--------------| | | | / | | | | |

Registration Once the pledge successfully completes the CoJP exchange and becomes a network node, it obtains the network prefix from neighboring routers and registers its IPv6 addresses. As detailed in , the combined 6LoWPAN ND 6LBR and Root of the RPL network learn information such as an identifier (device EUI-64 or a ROVR (from 6LoWPAN ND)) and the updated Sequence Number (from RPL), and perform 6LoWPAN ND proxy registration to the 6BBR on behalf of the LLN nodes. illustrates the initial IPv6 signaling that enables a 6LN to form a global address and register it to a 6LBR using 6LoWPAN ND . It is then carried over RPL to the RPL Root and then to the 6BBR. This flow happens just once when the address is created and first registered.

Initial Registration Flow over Multi-Link Subnet 6LoWPAN Node 6LR 6LBR 6BBR (RPL leaf) (router) (Root) | | | | | 6LoWPAN ND |6LoWPAN ND+RPL | 6LoWPAN ND | IPv6 ND | LLN link |Route-Over mesh|Ethernet/serial| Backbone | | | | | RS (mcast) | | | |-------------->| | | |-----------> | | | |------------------> | | | RA (unicast) | | | |<--------------| | | | | | | | NS(EARO) | | | |-------------->| | | | 6LoWPAN ND | Extended DAR | | | |-------------->| | | | | NS(EARO) | | | |-------------->| | | | | NS-DAD | | | |------> | | | | (EARO) | | | | | | | NA(EARO) |<timeout> | | |<--------------| | | Extended DAC | | | |<--------------| | | NA(EARO) | | | |<--------------| | | | | | |

illustrates the repeating IPv6 signaling that enables a 6LN to keep a global address alive and registered with its 6LBR using 6LoWPAN ND to the 6LR, RPL to the RPL Root, and then 6LoWPAN ND again to the 6BBR, which avoids repeating the Extended DAR/DAC flow across the network when RPL can suffice as a keep-alive mechanism.

Next Registration Flow over Multi-Link Subnet 6LoWPAN Node 6LR 6LBR 6BBR (RPL leaf) (router) (Root) | | | | | 6LoWPAN ND |6LoWPAN ND+RPL | 6LoWPAN ND | IPv6 ND | LLN link |Route-Over mesh| ant IPv6 link | Backbone | | | | | | | | NS(EARO) | | | |-------------->| | | | NA(EARO) | | | |<--------------| | | | | DAO | | | |-------------->| | | | DAO-ACK | | | |<--------------| | | | | NS(EARO) | | | |-------------->| | | | NA(EARO) | | | |<--------------| | | | | | | | |

As the network builds up, a node should start as a leaf to join the RPL network and may later turn into both a RPL-capable router and a 6LR, so as to accept leaf nodes recursively joining the network.

TSCH and 6top

6top 6TiSCH expects a high degree of scalability together with a distributed routing functionality based on RPL. To achieve this goal, the spectrum must be allocated in a way that allows for spatial reuse between zones that will not interfere with one another. In a large and spatially distributed network, a 6TiSCH node is often in a good position to determine usage of the spectrum in its vicinity. With 6TiSCH, the abstraction of an IPv6 link is implemented as a pair of bundles of cells, one in each direction. IP links are only enabled between RPL parents and children. The 6TiSCH operation is optimal when the size of a bundle minimizes both the energy wasted in idle listening and the packet drops due to congestion loss, while packets are forwarded within an acceptable latency. Use cases for distributed routing are often associated with a statistical distribution of best-effort traffic with variable needs for bandwidth on each individual link. The 6TiSCH operation can remain optimal if RPL parents can adjust, dynamically and with enough reactivity to match the variations of best-effort traffic, the amount of bandwidth that is used to communicate between themselves and their children, in both directions. In turn, the agility to fulfill the needs for additional cells improves when the number of interactions with other devices and the protocol latencies are minimized. 6top is a logical link control sitting between the IP layer and the TSCH MAC layer, which provides the link abstraction that is required for IP operations. The 6top Protocol, 6P, which is specified in , is one of the services provided by 6top. In particular, the 6top services are available over a management API that enables an external management entity to schedule cells and slotframes, and allows the addition of complementary functionality, for instance, a Scheduling Function that manages a dynamic schedule based on observed resource usage as discussed in . For this purpose, the 6TiSCH architecture differentiates "soft" cells and "hard" cells.

Hard Cells "Hard" cells are cells that are owned and managed by a separate scheduling entity (e.g., a PCE) that specifies the slotOffset/channelOffset of the cells to be added/moved/deleted, in which case 6top can only act as instructed and may not move hard cells in the TSCH schedule on its own.

Soft Cells In contrast, "soft" cells are cells that 6top can manage locally. 6top contains a monitoring process that monitors the performance of cells and that can add and remove soft cells in the TSCH schedule to adapt to the traffic needs, or move one when it performs poorly. To reserve a soft cell, the higher layer does not indicate the exact slotOffset/channelOffset of the cell to add, but rather the resulting bandwidth and QoS requirements. When the monitoring process triggers a cell reallocation, the two neighbor devices communicating over this cell negotiate its new position in the TSCH schedule.

Scheduling Functions and the 6top Protocol In the case of soft cells, the cell management entity that controls the dynamic attribution of cells to adapt to the dynamics of variable rate flows is called a Scheduling Function (SF). There may be multiple SFs that react more or less aggressively to the dynamics of the network. An SF may be seen as divided between an upper bandwidth-adaptation logic that is unaware of the particular technology used to obtain and release bandwidth and an underlying service that maps those needs in the actual technology. In the case of TSCH using the 6top Protocol as illustrated in , this means mapping the bandwidth onto cells.

SF/6P Stack in 6top +------------------------+ +------------------------+ | Scheduling Function | | Scheduling Function | | Bandwidth adaptation | | Bandwidth adaptation | +------------------------+ +------------------------+ | Scheduling Function | | Scheduling Function | | TSCH mapping to cells | | TSCH mapping to cells | +------------------------+ +------------------------+ | 6top cells negotiation | <- 6P -> | 6top cells negotiation | +------------------------+ +------------------------+ Device A Device B

The SF relies on 6top services that implement the 6top Protocol (6P) to negotiate the precise cells that will be allocated or freed based on the schedule of the peer. For instance, it may be that a peer wants to use a particular timeslot that is free in its schedule, but that timeslot is already in use by the other peer to communicate with a third party on a different cell. 6P enables the peers to find an agreement in a transactional manner that ensures the final consistency of the nodes' state. MSF is one of the possible Scheduling Functions. MSF uses the rendezvous slot from for network discovery, neighbor discovery, and any other broadcast. For basic unicast communication with any neighbor, each node uses a receive cell at a well-known slotOffset/channelOffset, which is derived from a hash of their own MAC address. Nodes can reach any neighbor by installing a transmit (shared) cell with slotOffset/channelOffset derived from the neighbor's MAC address. For child-parent links, MSF continuously monitors the load between parents and children. It then uses 6P to install or remove unicast cells whenever the current schedule appears to be under-provisioned or over-provisioned.

6top and RPL Objective Function Operations An implementation of a RPL Objective Function (OF), such as the RPL Objective Function Zero (OF0) that is used in the Minimal 6TiSCH Configuration to support RPL over a static schedule, may leverage for its internal computation the information maintained by 6top. An OF may require metrics about reachability, such as the Expected Transmission Count (ETX) metric . 6top creates and maintains an abstract neighbor table, and this state may be leveraged to feed an OF and/or store OF information as well. A neighbor table entry may contain a set of statistics with respect to that specific neighbor. The neighbor information may include the time when the last packet has been received from that neighbor, a set of cell quality metrics, e.g., received signal strength indication (RSSI) or link quality indicator (LQI), the number of packets sent to the neighbor, or the number of packets received from it. This information can be made available through 6top management APIs and used, for instance, to compute a Rank Increment that will determine the selection of the preferred parent. 6top provides statistics about the underlying layer so the OF can be tuned to the nature of the TSCH MAC layer. 6top also enables the RPL OF to influence the MAC behavior, for instance, by configuring the periodicity of IEEE Std 802.15.4 Extended Beacons (EBs). By augmenting the EB periodicity, it is possible to change the network dynamics so as to improve the support of devices that may change their point of attachment in the 6TiSCH network. Some RPL control messages, such as the DODAG Information Object (DIO), are ICMPv6 messages that are broadcast to all neighbor nodes. With 6TiSCH, the broadcast channel requirement is addressed by 6top by configuring TSCH to provide a broadcast channel, as opposed to, for instance, piggybacking the DIO messages in Layer 2 Enhanced Beacons (EBs), which would produce undue timer coupling among layers and packet size issues, and could conflict with the policy of production networks where EBs are mostly eliminated to conserve energy.

Network Synchronization Nodes in a TSCH network must be time synchronized. A node keeps synchronized to its time source neighbor through a combination of frame-based and acknowledgment-based synchronization. To maximize battery life and network throughput, it is advisable that RPL ICMP discovery and maintenance traffic (governed by the Trickle timer) be somehow coordinated with the transmission of time synchronization packets (especially with Enhanced Beacons). This could be achieved through an interaction of the 6top sublayer and the RPL Objective Function, or could be controlled by a management entity. Time distribution requires a loop-free structure. Nodes caught in a synchronization loop will rapidly desynchronize from the network and become isolated. 6TiSCH uses a RPL DAG with a dedicated global Instance for the purpose of time synchronization. That Instance is referred to as the Time Synchronization Global Instance (TSGI). The TSGI can be operated in either of the three modes that are detailed in Section of RPL, "Instances, DODAGs, and DODAG Versions". Multiple uncoordinated DODAGs with independent Roots may be used if all the Roots share a common time source such as the Global Positioning System (GPS). In the absence of a common time source, the TSGI should form a single DODAG with a virtual Root. A backbone network is then used to synchronize and coordinate RPL operations between the Backbone Routers that act as sinks for the LLN. Optionally, RPL's periodic operations may be used to transport the network synchronization. This may mean that 6top would need to trigger (override) the Trickle timer if no other traffic has occurred for such a time that nodes may get out of synchronization. A node that has not joined the TSGI advertises a MAC-level Join Priority of 0xFF to notify its neighbors that is not capable of serving as time parent. A node that has joined the TSGI advertises a MAC-level Join Priority set to its DAGRank() in that Instance, where DAGRank() is the operation specified in Section of , "Rank Comparison". The provisioning of a RPL Root is out of scope for both RPL and this architecture, whereas RPL enables the propagation of configuration information down the DODAG. This applies to the TSGI as well; a Root is configured, or obtains by unspecified means, the knowledge of the RPLInstanceID for the TSGI. The Root advertises its DagRank in the TSGI, which must be less than 0xFF, as its Join Priority in its IEEE Std 802.15.4 EBs. A node that reads a Join Priority of less than 0xFF should join the neighbor with the lesser Join Priority and use it as time parent. If the node is configured to serve as time parent, then the node should join the TSGI, obtain a Rank in that Instance, and start advertising its own DagRank in the TSGI as its Join Priority in its EBs.

Slotframes and CDU Matrix 6TiSCH enables IPv6 best-effort (stochastic) transmissions over a MAC layer that is also capable of scheduled (deterministic) transmissions. A window of time is defined around the scheduled transmission where the medium must, as much as practically feasible, be free of contending energy to ensure that the medium is free of contending packets when the time comes for a scheduled transmission. One simple way to obtain such a window is to format time and frequencies in cells of transmission of equal duration. This is the method that is adopted in IEEE Std 802.15.4 TSCH as well as the Long Term Evolution (LTE) of cellular networks. The 6TiSCH architecture defines a global concept that is called a Channel Distribution and Usage (CDU) matrix to describe that formatting of time and frequencies. A CDU matrix is defined centrally as part of the network definition. It is a matrix of cells with a height equal to the number of available channels (indexed by channelOffsets) and a width (in timeslots) that is the period of the network scheduling operation (indexed by slotOffsets) for that CDU matrix. There are different models for scheduling the usage of the cells, which place the responsibility of avoiding collisions either on a central controller or on the devices themselves, at an extra cost in terms of energy to scan for free cells (more in ). The size of a cell is a timeslot duration, and values of 10 to 15 milliseconds are typical in 802.15.4 TSCH to accommodate for the transmission of a frame and an ack, including the security validation on the receive side, which may take up to a few milliseconds on some device architecture. A CDU matrix iterates over a well-known channel rotation called the hopping sequence. In a given network, there might be multiple CDU matrices that operate with different widths, so they have different durations and represent different periodic operations. It is recommended that all CDU matrices in a 6TiSCH domain operate with the same cell duration and are aligned so as to reduce the chances of interferences from the Slotted ALOHA operations. The knowledge of the CDU matrices is shared between all the nodes and used in particular to define slotframes. A slotframe is a MAC-level abstraction that is common to all nodes and contains a series of timeslots of equal length and precedence. It is characterized by a slotframe_ID and a slotframe_size. A slotframe aligns to a CDU matrix for its parameters, such as number and duration of timeslots. Multiple slotframes can coexist in a node schedule, i.e., a node can have multiple activities scheduled in different slotframes. A slotframe is associated with a priority that may be related to the precedence of different 6TiSCH topologies. The slotframes may be aligned to different CDU matrices and thus have different widths. There is typically one slotframe for scheduled traffic that has the highest precedence and one or more slotframe(s) for RPL traffic. The timeslots in the slotframe are indexed by the slotOffset; the first cell is at slotOffset 0. When a packet is received from a higher layer for transmission, 6top inserts that packet in the outgoing queue that matches the packet best (Differentiated Services can therefore be used). At each scheduled transmit slot, 6top looks for the frame in all the outgoing queues that best matches the cells. If a frame is found, it is given to the TSCH MAC for transmission.

Distributing the Reservation of Cells The 6TiSCH architecture introduces the concept of chunks () to distribute the allocation of the spectrum for a whole group of cells at a time. The CDU matrix is formatted into a set of chunks, possibly as illustrated in , each of the chunks identified uniquely by a chunk-ID. The knowledge of this formatting is shared between all the nodes in a 6TiSCH network. It could be conveyed during the join process, codified into a profile document, or obtained using some other mechanism. This is as opposed to Static Scheduling, which refers to the preprogrammed mechanism specified in and which existed before the distribution of the chunk formatting.

CDU Matrix Partitioning in Chunks +-----+-----+-----+-----+-----+-----+-----+ +-----+ chan.Off. 0 |chnkA|chnkP|chnk7|chnkO|chnk2|chnkK|chnk1| ... |chnkZ| +-----+-----+-----+-----+-----+-----+-----+ +-----+ chan.Off. 1 |chnkB|chnkQ|chnkA|chnkP|chnk3|chnkL|chnk2| ... |chnk1| +-----+-----+-----+-----+-----+-----+-----+ +-----+ ... +-----+-----+-----+-----+-----+-----+-----+ +-----+ chan.Off. 15 |chnkO|chnk6|chnkN|chnk1|chnkJ|chnkZ|chnkI| ... |chnkG| +-----+-----+-----+-----+-----+-----+-----+ +-----+ 0 1 2 3 4 5 6 M

The 6TiSCH architecture envisions a protocol that enables chunk ownership appropriation whereby a RPL parent discovers a chunk that is not used in its interference domain, claims the chunk, and then defends it in case another RPL parent would attempt to appropriate it while it is in use. The chunk is the basic unit of ownership that is used in that process. As a result of the process of chunk ownership appropriation, the RPL parent has exclusive authority to decide which cell in the appropriated chunk can be used by which node in its interference domain. In other words, it is implicitly delegated the right to manage the portion of the CDU matrix that is represented by the chunk. Initially, those cells are added to the heap of free cells, then dynamically placed into existing bundles, into new bundles, or allocated opportunistically for one transmission. Note that a PCE is expected to have precedence in the allocation, so that a RPL parent would only be able to obtain portions that are not in use by the PCE.

Schedule Management Mechanisms 6TiSCH uses four paradigms to manage the TSCH schedule of the LLN nodes: Static Scheduling, Neighbor-to-Neighbor Scheduling, Remote Monitoring and Scheduling Management, and Hop-by-Hop Scheduling. Multiple mechanisms are defined that implement the associated Interaction Models, and they can be combined and used in the same LLN. Which mechanism(s) to use depends on application requirements.

Static Scheduling In the simplest instantiation of a 6TiSCH network, a common fixed schedule may be shared by all nodes in the network. Cells are shared, and nodes contend for slot access in a Slotted ALOHA manner. A static TSCH schedule can be used to bootstrap a network, as an initial phase during implementation or as a fall-back mechanism in case of network malfunction. This schedule is preestablished, for instance, decided by a network administrator based on operational needs. It can be preconfigured into the nodes, or, more commonly, learned by a node when joining the network using standard IEEE Std 802.15.4 Information Elements (IE). Regardless, the schedule remains unchanged after the node has joined a network. RPL is used on the resulting network. This "minimal" scheduling mechanism that implements this paradigm is detailed in .

Neighbor-to-Neighbor Scheduling In the simplest instantiation of a 6TiSCH network described in , nodes may expect a packet at any cell in the schedule and will waste energy idle listening. In a more complex instantiation of a 6TiSCH network, a matching portion of the schedule is established between peers to reflect the observed amount of transmissions between those nodes. The aggregation of the cells between a node and a peer forms a bundle that the 6top sublayer uses to implement the abstraction of a link for IP. The bandwidth on that link is proportional to the number of cells in the bundle. If the size of a bundle is configured to fit an average amount of bandwidth, peak traffic is dropped. If the size is configured to allow for peak emissions, energy is wasted idle listening. As discussed in more detail in , the 6top Protocol specifies the exchanges between neighbor nodes to reserve soft cells to transmit to one another, possibly under the control of a Scheduling Function (SF). Because this reservation is done without global knowledge of the schedule of the other nodes in the LLN, scheduling collisions are possible. And as discussed in , an optional SF is used to monitor bandwidth usage and to perform requests for dynamic allocation by the 6top sublayer. The SF component is not part of the 6top sublayer. It may be co-located on the same device or may be partially or fully offloaded to an external system. The "6TiSCH Minimal Scheduling Function (MSF)" provides a simple SF that can be used by default by devices that support dynamic scheduling of soft cells. Monitoring and relocation is done in the 6top sublayer. For the upper layer, the connection between two neighbor nodes appears as a number of cells. Depending on traffic requirements, the upper layer can request 6top to add or delete a number of cells scheduled to a particular neighbor, without being responsible for choosing the exact slotOffset/channelOffset of those cells.

Remote Monitoring and Schedule Management Remote Monitoring and Schedule Management refers to a DetNet/SDN model whereby an NME and a scheduling entity, associated with a PCE, reside in a central controller and interact with the 6top sublayer to control IPv6 links and Tracks () in a 6TiSCH network. The composite centralized controller can assign physical resources (e.g., buffers and hard cells) to a particular Track to optimize the reliability within a bounded latency for a well-specified flow. The work in the 6TiSCH Working Group focused on nondeterministic traffic and did not provide the generic data model necessary for the controller to monitor and manage resources of the 6top sublayer. This is deferred to future work, see . With respect to centralized routing and scheduling, it is envisioned that the related component of the 6TiSCH architecture would be an extension of the DetNet architecture, which studies Layer 3 aspects of Deterministic Networks and covers networks that span multiple Layer 2 domains. The DetNet architecture is a form of Software-Defined Networking (SDN) architecture and is composed of three planes: a (User) Application Plane, a Controller Plane (where the PCE operates), and a Network Plane, which can represent a 6TiSCH LLN. "Software-Defined Networking (SDN): Layers and Architecture Terminology" proposes a generic representation of the SDN architecture that is reproduced in .

SDN Layers and Architecture Terminology per RFC 7426 o--------------------------------o | | | +-------------+ +----------+ | | | Application | | Service | | | +-------------+ +----------+ | | Application Plane | o---------------Y----------------o | *-----------------------------Y---------------------------------* | Network Services Abstraction Layer (NSAL) | *------Y------------------------------------------------Y-------* | | | Service Interface | | | o------Y------------------o o---------------------Y------o | | Control Plane | | Management Plane | | | +----Y----+ +-----+ | | +-----+ +----Y----+ | | | Service | | App | | | | App | | Service | | | +----Y----+ +--Y--+ | | +--Y--+ +----Y----+ | | | | | | | | | | *----Y-----------Y----* | | *---Y---------------Y----* | | | Control Abstraction | | | | Management Abstraction | | | | Layer (CAL) | | | | Layer (MAL) | | | *----------Y----------* | | *----------Y-------------* | | | | | | | o------------|------------o o------------|---------------o | | | CP | MP | Southbound | Southbound | Interface | Interface | | *------------Y---------------------------------Y----------------* | Device and resource Abstraction Layer (DAL) | *------------Y---------------------------------Y----------------* | | | | | o-------Y----------o +-----+ o--------Y----------o | | | Forwarding Plane | | App | | Operational Plane | | | o------------------o +-----+ o-------------------o | | Network Device | +---------------------------------------------------------------+

The PCE establishes end-to-end Tracks of hard cells, which are described in more detail in . The DetNet work is expected to enable end-to-end deterministic paths across heterogeneous networks. This can be, for instance, a 6TiSCH LLN and an Ethernet backbone. This model fits the 6TiSCH extended configuration, whereby a 6BBR federates multiple 6TiSCH LLNs in a single subnet over a backbone that can be, for instance, Ethernet or Wi-Fi. In that model, 6TiSCH 6BBRs synchronize with one another over the backbone, so as to ensure that the multiple LLNs that form the IPv6 subnet stay tightly synchronized. If the backbone is deterministic, then the Backbone Router ensures that the end-to-end deterministic behavior is maintained between the LLN and the backbone. It is the responsibility of the PCE to compute a deterministic path end to end across the TSCH network and an IEEE Std 802.1 TSN Ethernet backbone, and it is the responsibility of DetNet to enable end-to-end deterministic forwarding.

Hop-by-Hop Scheduling A node can reserve a Track to one or more destination(s) that are multiple hops away by installing soft cells at each intermediate node. This forms a Track of soft cells. A Track SF above the 6top sublayer of each node on the Track is needed to monitor these soft cells and trigger relocation when needed. This hop-by-hop reservation mechanism is expected to be similar in essence to and/or and . The protocol for a node to trigger hop-by-hop scheduling is not yet defined.

On Tracks The architecture introduces the concept of a Track, which is a directed path from a source 6TiSCH node to one or more destination 6TiSCH node(s) across a 6TiSCH LLN. A Track is the 6TiSCH instantiation of the concept of a deterministic path as described in . Constrained resources such as memory buffers are reserved for that Track in intermediate 6TiSCH nodes to avoid loss related to limited capacity. A 6TiSCH node along a Track not only knows which bundles of cells it should use to receive packets from a previous hop but also knows which bundle(s) it should use to send packets to its next hop along the Track.

General Behavior of Tracks A Track is associated with Layer 2 bundles of cells with related schedules and logical relationships that ensure that a packet that is injected in a Track will progress in due time all the way to destination. Multiple cells may be scheduled in a Track for the transmission of a single packet, in which case the normal operation of IEEE Std 802.15.4 Automatic Repeat-reQuest (ARQ) can take place; the acknowledgment may be omitted in some cases, for instance, if there is no scheduled cell for a possible retry. There are several benefits for using a Track to forward a packet from a source node to the destination node:

1. Track Forwarding, as further described in , is a Layer 2 forwarding scheme, which introduces less process delay and overhead than a Layer 3 forwarding scheme. Therefore, LLN devices can save more energy and resources, which is critical for resource-constrained devices.
2. Since channel resources, i.e., bundles of cells, have been reserved for communications between 6TiSCH nodes of each hop on the Track, the throughput and the maximum latency of the traffic along a Track are guaranteed, and the jitter is minimized.
3. By knowing the scheduled timeslots of incoming bundle(s) and outgoing bundle(s), 6TiSCH nodes on a Track could save more energy by staying in sleep state during inactive slots.
4. Tracks are protected from interfering with one another if a cell is scheduled to belong to at most one Track, and congestion loss is avoided if at most one packet can be presented to the MAC to use that cell. Tracks enhance the reliability of transmissions and thus further improve the energy consumption in LLN devices by reducing the chances of retransmission.

Serial Track A Serial (or simple) Track is the 6TiSCH version of a circuit: a bundle of cells that are programmed to receive (RX-cells) is uniquely paired with a bundle of cells that are set to transmit (TX-cells), representing a Layer 2 forwarding state that can be used regardless of the network-layer protocol. A Serial Track is thus formed end-to-end as a succession of paired bundles: a receive bundle from the previous hop and a transmit bundle to the next hop along the Track. For a given iteration of the device schedule, the effective channel of the cell is obtained by looping through a well-known hopping sequence beginning at Epoch time and starting at the cell's channelOffset, which results in a rotation of the frequency that is used for transmission. The bundles may be computed so as to accommodate both variable rates and retransmissions, so they might not be fully used in the iteration of the schedule.

Complex Track with Replication and Elimination The art of Deterministic Networks already includes packet replication and elimination techniques. Example standards include the Parallel Redundancy Protocol (PRP) and the High-availability Seamless Redundancy (HSR) . Similarly, and as opposed to a Serial Track that is a sequence of nodes and links, a Complex Track is shaped as a directed acyclic graph towards one or more destination(s) to support multipath forwarding and route around failures. A Complex Track may branch off over noncongruent branches for the purpose of multicasting and/or redundancy, in which case, it reconverges later down the path. This enables the Packet Replication, Elimination, and Ordering Functions (PREOF) defined by DetNet. Packet ARQ, Replication, Elimination, and Overhearing (PAREO) adds radio-specific capabilities of Layer 2 ARQ and promiscuous listening to redundant transmissions to compensate for the lossiness of the medium and meet industrial expectations of a RAW network. Combining PAREO and PREOF, a Track may extend beyond the 6TiSCH network into a larger DetNet network. In the art of TSCH, a path does not necessarily support PRE, but it is almost systematically multipath. This means that a Track is scheduled so as to ensure that each hop has at least two forwarding solutions, and the forwarding decision is to try the preferred one and use the other in case of Layer 2 transmission failure as detected by ARQ. Similarly, at each 6TiSCH hop along the Track, the PCE may schedule more than one timeslot for a packet, so as to support Layer 2 retries (ARQ). It is also possible that the field device only uses the second branch if sending over the first branch fails.

DetNet End-to-End Path Ultimately, DetNet should enable extending a Track beyond the 6TiSCH LLN as illustrated in . In that example, a Track is laid out from a field device in a 6TiSCH network to an IoT gateway that is located on an 802.1 Time-Sensitive Networking (TSN) backbone. A 6TiSCH-aware DetNet service layer handles the Packet Replication, Elimination, and Ordering Functions over the DODAG that forms a Track. The Replication function in the 6TiSCH Node sends a copy of each packet over two different branches, and the PCE schedules each hop of both branches so that the two copies arrive in due time at the gateway. In case of a loss on one branch, hopefully the other copy of the packet still makes it in due time. If two copies make it to the IoT gateway, the Elimination function in the gateway ignores the extra packet and presents only one copy to upper layers.

Example End-to-End DetNet Track +-=-=-+ | IoT | | G/W | +-=-=-+ ^ <=== Elimination Track branch | | +-=-=-=-+ +-=-=-=-=+ Subnet backbone | | +-=|-=+ +-=|-=+ | | | Backbone | | | Backbone o | | | Router | | | Router +-=/-=+ +-=|-=+ o / o o-=-o-=-=/ o o o-=-o-=/ o o o o o o \ / o o LLN o o v <=== Replication o

Cell Reuse The 6TiSCH architecture provides the means to avoid waste of cells as well as overflows in the transmit bundle of a Track, as follows: A TX-cell that is not needed for the current iteration may be reused opportunistically on a per-hop basis for routed packets. When all of the frames that were received for a given Track are effectively transmitted, any available TX-cell for that Track can be reused for upper-layer traffic for which the next-hop router matches the next hop along the Track. In that case, the cell that is being used is effectively a TX-cell from the Track, but the short address for the destination is that of the next-hop router. It results in a frame that is received in an RX-cell of a Track with a destination MAC address set to this node, as opposed to the broadcast MAC address that must be extracted from the Track and delivered to the upper layer. Note that a frame with an unrecognized destination MAC address is dropped at the lower MAC layer and thus is not received at the 6top sublayer. On the other hand, it might happen that there are not enough TX-cells in the transmit bundle to accommodate the Track traffic, for instance, if more retransmissions are needed than provisioned. In that case, and if the frame transports an IPv6 packet, then it can be placed for transmission in the bundle that is used for Layer 3 traffic towards the next hop along the Track. The MAC address should be set to the next-hop MAC address to avoid confusion. It results in a frame that is received over a Layer 3 bundle that may be in fact associated with a Track. In a classical IP link such as an Ethernet, off-Track traffic is typically in excess over reservation to be routed along the non-reserved path based on its QoS setting. But with 6TiSCH, since the use of the Layer 3 bundle may be due to transmission failures, it makes sense for the receiver to recognize a frame that should be re-Tracked and to place it back on the appropriate bundle if possible. A frame is re-Tracked by scheduling it for transmission over the transmit bundle associated with the Track, with the destination MAC address set to broadcast.

Forwarding Models By forwarding, this document means the per-packet operation that allows delivery of a packet to a next hop or an upper layer in this node. Forwarding is based on preexisting state that was installed as a result of a routing computation, see . 6TiSCH supports three different forwarding models: (GMPLS) Track Forwarding, (classical) IPv6 Forwarding, and (6LoWPAN) Fragment Forwarding.

Track Forwarding Forwarding along a Track can be seen as a Generalized Multiprotocol Label Switching (GMPLS) operation in that the information used to switch a frame is not an explicit label but is rather related to other properties of the way the packet was received, a particular cell in the case of 6TiSCH. As a result, as long as the TSCH MAC (and Layer 2 security) accepts a frame, that frame can be switched regardless of the protocol, whether this is an IPv6 packet, a 6LoWPAN fragment, or a frame from an alternate protocol such as WirelessHART or ISA100.11a. A data frame that is forwarded along a Track normally has a destination MAC address that is set to broadcast or a multicast address depending on MAC support. This way, the MAC layer in the intermediate nodes accepts the incoming frame and 6top switches it without incurring a change in the MAC header. In the case of IEEE Std 802.15.4, this means effectively to broadcast, so that along the Track the short address for the destination of the frame is set to 0xFFFF. There are two modes for a Track: an IPv6 native mode and a protocol-independent tunnel mode.

Native Mode In native mode, the Protocol Data Unit (PDU) is associated with flow-dependent metadata that refers uniquely to the Track, so the 6top sublayer can place the frame in the appropriate cell without ambiguity. In the case of IPv6 traffic, this flow may be identified using a 6-tuple as discussed in . In particular, implementations of this document should support identification of DetNet flows based on the IPv6 Flow Label field. The flow follows a Track that is identified using a RPL Instance (see ), signaled in a RPL Packet Information (more in ) and the source address of a packet going down the DODAG formed by a local instance. One or more flows may be placed in a same Track and the Track identification (TrackID plus owner) may be placed in an IP-in-IP encapsulation. The forwarding operation is based on the Track and does not depend on the flow therein. The Track identification is validated at egress before restoring the destination MAC address (DMAC) and punting to the upper layer. illustrates the Track Forwarding operation that happens at the 6top sublayer, below IP.

Track Forwarding, Native Mode | Packet flowing across the network ^ +--------------+ | | | IPv6 | | | +--------------+ | | | 6LoWPAN HC | | | +--------------+ ingress egress | 6top | sets +----+ +----+ restores +--------------+ DMAC to | | | | DMAC to | TSCH MAC | brdcst | | | | dest +--------------+ | | | | | | | LLN PHY | +-------+ +--...-----+ +-------+ +--------------+ Ingress Relay Relay Egress Stack Layer Node Node Node Node

Tunnel Mode In tunnel mode, the frames originate from an arbitrary protocol over a compatible MAC that may or may not be synchronized with the 6TiSCH network. An example of this would be a router with a dual radio that is capable of receiving and sending WirelessHART or ISA100.11a frames with the second radio by presenting itself as an access point or a Backbone Router, respectively. In that mode, some entity (e.g., PCE) can coordinate with a WirelessHART Network Manager or an ISA100.11a System Manager to specify the flows that are transported.

Track Forwarding, Tunnel Mode +--------------+ | IPv6 | +--------------+ | 6LoWPAN HC | +--------------+ set restore | 6top | +DMAC+ +DMAC+ +--------------+ to|brdcst to|nexthop | TSCH MAC | | | | | +--------------+ | | | | | LLN PHY | +-------+ +--...-----+ +-------+ +--------------+ | ingress egress | | | +--------------+ | | | LLN PHY | | | +--------------+ | Packet flowing across the network | | TSCH MAC | | | +--------------+ | DMAC = | DMAC = |ISA100/WiHART | | nexthop v nexthop +--------------+ Source Ingress Egress Destination Stack Layer Node Node Node Node

In that case, the TrackID that identifies the Track at the ingress 6TiSCH router is derived from the RX-cell. The DMAC is set to this node, but the TrackID indicates that the frame must be tunneled over a particular Track, so the frame is not passed to the upper layer. Instead, the DMAC is forced to broadcast, and the frame is passed to the 6top sublayer for switching. At the egress 6TiSCH router, the reverse operation occurs. Based on tunneling information of the Track, which may for instance indicate that the tunneled datagram is an IP packet, the datagram is passed to the appropriate link-layer with the destination MAC restored.

Tunneling Information Tunneling information coming with the Track configuration provides the destination MAC address of the egress endpoint as well as the tunnel mode and specific data depending on the mode, for instance, a service access point for frame delivery at egress. If the tunnel egress point does not have a MAC address that matches the configuration, the Track installation fails. If the Layer 3 destination address belongs to the tunnel termination, then it is possible that the IPv6 address of the destination is compressed at the 6LoWPAN sublayer based on the MAC address. Restoring the wrong MAC address at the egress would then also result in the wrong IP address in the packet after decompression. For that reason, a packet can be injected in a Track only if the destination MAC address is effectively that of the tunnel egress point. It is thus mandatory for the ingress router to validate that the MAC address used at the 6LoWPAN sublayer for compression matches that of the tunnel egress point before it overwrites it to broadcast. The 6top sublayer at the tunnel egress point reverts that operation to the MAC address obtained from the tunnel information.

IPv6 Forwarding As the packets are routed at Layer 3, traditional QoS and Active Queue Management (AQM) operations are expected to prioritize flows.

IP Forwarding | Packet flowing across the network ^ +--------------+ | | | IPv6 | | +-QoS+ +-QoS+ | +--------------+ | | | | | | | 6LoWPAN HC | | | | | | | +--------------+ | | | | | | | 6top | | | | | | | +--------------+ | | | | | | | TSCH MAC | | | | | | | +--------------+ | | | | | | | LLN PHY | +-------+ +--...-----+ +-------+ +--------------+ Source Ingress Egress Destination Stack Layer Node Router Router Node

Fragment Forwarding Considering that, per , 6LoWPAN packets can be as large as 1280 bytes (the IPv6 minimum MTU) and that the non-storing mode of RPL implies source routing, which requires space for routing headers, and that an IEEE Std 802.15.4 frame with security may carry in the order of 80 bytes of effective payload, an IPv6 packet might be fragmented into more than 16 fragments at the 6LoWPAN sublayer. This level of fragmentation is much higher than that traditionally experienced over the Internet with IPv4 fragments, where fragmentation is already known as harmful. In the case of a multihop route within a 6TiSCH network, hop-by-hop recomposition occurs at each hop to reform the packet and route it. This creates additional latency and forces intermediate nodes to store a portion of a packet for an undetermined time, thus impacting critical resources such as memory and battery. describes a framework for forwarding fragments end-to-end across a 6TiSCH route-over mesh. Within that framework, details a virtual reassembly buffer mechanism whereby the datagram tag in the 6LoWPAN fragment is used as a label for switching at the 6LoWPAN sublayer. Building on this technique, introduces a new format for 6LoWPAN fragments that enables the selective recovery of individual fragments and allows for a degree of flow control based on an Explicit Congestion Notification (ECN).

Forwarding First Fragment | Packet flowing across the network ^ +--------------+ | | | IPv6 | | +----+ +----+ | +--------------+ | | | | | | | 6LoWPAN HC | | learn learn | +--------------+ | | | | | | | 6top | | | | | | | +--------------+ | | | | | | | TSCH MAC | | | | | | | +--------------+ | | | | | | | LLN PHY | +-------+ +--...-----+ +-------+ +--------------+ Source Ingress Egress Destination Stack Layer Node Router Router Node

In that model, the first fragment is routed based on the IPv6 header that is present in that fragment. The 6LoWPAN sublayer learns the next-hop selection, generates a new datagram tag for transmission to the next hop, and stores that information indexed by the incoming MAC address and datagram tag. The next fragments are then switched based on that stored state.

Forwarding Next Fragment | Packet flowing across the network ^ +--------------+ | | | IPv6 | | | +--------------+ | | | 6LoWPAN HC | | replay replay | +--------------+ | | | | | | | 6top | | | | | | | +--------------+ | | | | | | | TSCH MAC | | | | | | | +--------------+ | | | | | | | LLN PHY | +-------+ +--...-----+ +-------+ +--------------+ Source Ingress Egress Destination Stack Layer Node Router Router Node

A bitmap and an ECN echo in the end-to-end acknowledgment enable the source to resend the missing fragments selectively. The first fragment may be resent to carve a new path in case of a path failure. The ECN echo set indicates that the number of outstanding fragments should be reduced.

Advanced 6TiSCH Routing

Packet Marking and Handling All packets inside a 6TiSCH domain must carry the RPLInstanceID that identifies the 6TiSCH topology (e.g., a Track) that is to be used for routing and forwarding that packet. The location of that information must be the same for all packets forwarded inside the domain. For packets that are routed by a PCE along a Track, the tuple formed by 1) (typically) the IPv6 source or (possibly) destination address in the IPv6 header and 2) a local RPLInstanceID in the RPI that serves as TrackID, identify uniquely the Track and associated transmit bundle. For packets that are routed by RPL, that information is the RPLInstanceID that is carried in the RPL Packet Information (RPI), as discussed in , "Loop Avoidance and Detection". The RPI is transported by a RPL Option in the IPv6 Hop-By-Hop Options header . A compression mechanism for the RPL packet artifacts that integrates the compression of IP-in-IP encapsulation and the Routing Header type 3 with that of the RPI in a 6LoWPAN dispatch/header type is specified in and . Either way, the method and format used for encoding the RPLInstanceID is generalized to all 6TiSCH topological Instances, which include both RPL Instances and Tracks.

Replication, Retries, and Elimination 6TiSCH supports the PREOF operations of elimination and reordering of packets along a complex Track, but has no requirement about tagging a sequence number in the packet for that purpose. With 6TiSCH, the schedule can tell when multiple receive timeslots correspond to copies of a same packet, in which case the receiver may avoid listening to the extra copies once it has received one instance of the packet. The semantics of the configuration enable correlated timeslots to be grouped for transmit (and receive, respectively) with 'OR' relations, and then an 'AND' relation can be configurable between groups. The semantics are such that if the transmit (and receive, respectively) operation succeeded in one timeslot in an 'OR' group, then all the other timeslots in the group are ignored. Now, if there are at least two groups, the 'AND' relation between the groups indicates that one operation must succeed in each of the groups. On the transmit side, timeslots provisioned for retries along a same branch of a Track are placed in the same 'OR' group. The 'OR' relation indicates that if a transmission is acknowledged, then retransmissions of that packet should not be attempted for the remaining timeslots in that group. There are as many 'OR' groups as there are branches of the Track departing from this node. Different 'OR' groups are programmed for the purpose of replication, each group corresponding to one branch of the Track. The 'AND' relation between the groups indicates that transmission over any of branches must be attempted regardless of whether a transmission succeeded in another branch. It is also possible to place cells to different next-hop routers in the same 'OR' group. This allows routing along multipath Tracks, trying one next hop and then another only if sending to the first fails. On the receive side, all timeslots are programmed in the same 'OR' group. Retries of the same copy as well as converging branches for elimination are converged, meaning that the first successful reception is enough and that all the other timeslots can be ignored. An 'AND' group denotes different packets that must all be received and transmitted over the associated transmit groups within their respected 'AND' or 'OR' rules. As an example, say that we have a simple network as represented in , and we want to enable PREOF between an ingress node I and an egress node E.

Scheduling PREOF on a Simple Network +-+ +-+ -- |A| ------ |C| -- / +-+ +-+ \ / \ +-+ +-+ |I| |E| +-+ +-+ \ / \ +-+ +-+ / -- |B| ------- |D| -- +-+ +-+

The assumption for this particular problem is that a 6TiSCH node has a single radio, so it cannot perform two receive and/or transmit operations at the same time, even on two different channels. Say we have six possible channels, and at least ten timeslots per slotframe. shows a possible schedule whereby each transmission is retried two or three times, and redundant copies are forwarded in parallel via A and C on the one hand, and B and D on the other, providing time diversity, spatial diversity though different physical paths, and frequency diversity.

Example Global Schedule slotOffset 0 1 2 3 4 5 6 7 9 +----+----+----+----+----+----+----+----+----+ channelOffset 0 | | | | | | |B->D| | | ... +----+----+----+----+----+----+----+----+----+ channelOffset 1 | |I->A| |A->C|B->D| | | | | ... +----+----+----+----+----+----+----+----+----+ channelOffset 2 |I->A| | |I->B| |C->E| |D->E| | ... +----+----+----+----+----+----+----+----+----+ channelOffset 3 | | | | |A->C| | | | | ... +----+----+----+----+----+----+----+----+----+ channelOffset 4 | | |I->B| | |B->D| | |D->E| ... +----+----+----+----+----+----+----+----+----+ channelOffset 5 | | |A->C| | | |C->E| | | ... +----+----+----+----+----+----+----+----+----+

This translates into a different slotframe that provides the waking and sleeping times for every node, and the channelOffset to be used when awake. shows the corresponding slotframe for node A.

Example Slotframe for Node A slotOffset 0 1 2 3 4 5 6 7 9 +----+----+----+----+----+----+----+----+----+ operation |rcv |rcv |xmit|xmit|xmit|none|none|none|none| ... +----+----+----+----+----+----+----+----+----+ channelOffset | 2 | 1 | 5 | 1 | 3 |N/A |N/A |N/A |N/A | ... +----+----+----+----+----+----+----+----+----+

The logical relationship between the timeslots is given by :

Node	rcv slotOffset	xmit slotOffset
I	N/A	(0 OR 1) AND (2 OR 3)
A	(0 OR 1)	(2 OR 3 OR 4)
B	(2 OR 3)	(4 OR 5 OR 6)
C	(2 OR 3 OR 4)	(5 OR 6)
D	(4 OR 5 OR 6)	(7 OR 8)
E	(5 OR 6 OR 7 OR 8)	N/A

IANA Considerations This document has no IANA actions.

Security Considerations The "Minimal Security Framework for 6TiSCH" was optimized for Low-Power and TSCH operations. The reader is encouraged to review the Security Considerations section of that document (Section ), which discusses 6TiSCH security issues in more details.

Availability of Remote Services The operation of 6TiSCH Tracks inherits its high-level operation from DetNet and is subject to the observations in . The installation and the maintenance of the 6TiSCH Tracks depend on the availability of a controller with a PCE to compute and push them in the network. When that connectivity is lost, existing Tracks may continue to operate until the end of their lifetime, but cannot be removed or updated, and new Tracks cannot be installed. In an LLN, the communication with a remote PCE may be slow and unreactive to rapid changes in the condition of the wireless communication. An attacker may introduce extra delay by selectively jamming some packets or some flows. The expectation is that the 6TiSCH Tracks enable enough redundancy to maintain the critical traffic in operation while new routes are calculated and programmed into the network. As with DetNet in general, the communication with the PCE must be secured and should be protected against DoS attacks, including delay injection and blackholing attacks, and secured as discussed in the security considerations defined for Abstraction and Control of Traffic Engineered Networks (ACTN) in , which applies equally to DetNet and 6TiSCH. In a similar manner, the communication with the JRC must be secured and should be protected against DoS attacks when possible.

Selective Jamming The hopping sequence of a TSCH network is well known, meaning that if a rogue manages to identify a cell of a particular flow, then it may selectively jam that cell without impacting any other traffic. This attack can be performed at the PHY layer without any knowledge of the Layer 2 keys, and it is very hard to detect and diagnose because only one flow is impacted. proposes a method to obfuscate the hopping sequence and make it harder to perpetrate that particular attack.

MAC-Layer Security This architecture operates on IEEE Std 802.15.4 and expects the link-layer security to be enabled at all times between connected devices, except for the very first step of the device join process, where a joining device may need some initial, unsecured exchanges so as to obtain its initial key material. In a typical deployment, all joined nodes use the same keys, and rekeying needs to be global. The 6TISCH architecture relies on the join process to deny authorization of invalid nodes and to preserve the integrity of the network keys. A rogue that managed to access the network can perform a large variety of attacks from DoS to injecting forged packets and routing information. "Zero-trust" properties would be highly desirable but are mostly not available at the time of this writing. is a notable exception that protects the ownership of IPv6 addresses and prevents a rogue node with L2 access from stealing and injecting traffic on behalf of a legitimate node.

Time Synchronization Time synchronization in TSCH induces another event horizon whereby a node will only communicate with another node if they are synchronized within a guard time. The pledge discovers the synchronization of the network based on the time of reception of the beacon. If an attacker synchronizes a pledge outside of the guard time of the legitimate nodes, then the pledge will never see a legitimate beacon and may not discover the attack. As discussed in , measures must be taken to protect the time synchronization, and for 6TiSCH this includes ensuring that the Absolute Slot Number (ASN), which is the node's sense of time, is not compromised. Once installed and as long as the node is synchronized to the network, ASN is implicit in the transmissions. IEEE Std 802.15.4 specifies that in a TSCH network, the nonce that is used for the computation of the Message Integrity Code (MIC) to secure link-layer frames is composed of the address of the source of the frame and of the ASN. The standard assumes that the ASN is distributed securely by other means. The ASN is not passed explicitly in the data frames and does not constitute a complete anti-replay protection. As a result, upper-layer protocols must provide a way to detect duplicates and cope with them. If the receiver and the sender have a different sense of ASN, the MIC will not validate and the frame will be dropped. In that sense, TSCH induces an event horizon whereby only nodes that have a common sense of ASN can talk to one another in an authenticated manner. With 6TiSCH, the pledge discovers a tentative ASN in beacons from nodes that have already joined the network. But even if the beacon can be authenticated, the ASN cannot be trusted as it could be a replay by an attacker, announcing an ASN that represents a time in the past. If the pledge uses an ASN that is learned from a replayed beacon for an encrypted transmission, a nonce-reuse attack becomes possible, and the network keys may be compromised.

Validating ASN After obtaining the tentative ASN, a pledge that wishes to join the 6TiSCH network must use a join protocol to obtain its security keys. The join protocol used in 6TiSCH is the Constrained Join Protocol (CoJP). In the minimal setting defined in , the authentication requires a pre-shared key, based on which a secure session is derived. The CoJP exchange may also be preceded by a zero-touch handshake in order to enable pledge joining based on certificates and/or inter-domain communication. As detailed in , a Join Proxy (JP) helps the pledge with the join procedure by relaying the link-scope Join Request over the IP network to a Join Registrar/Coordinator (JRC) that can authenticate the pledge and validate that it is attached to the appropriate network. As a result of the CoJP exchange, the pledge is in possession of link-layer material including keys and a short address, and if the ASN is known to be correct, all traffic can now be secured using CCM* at the link layer. The authentication steps must be such that they cannot be replayed by an attacker, and they must not depend on the tentative ASN being valid. During the authentication, the keying material that the pledge obtains from the JRC does not provide protection against spoofed ASN. Once the pledge has obtained the keys to use in the network, it may still need to verify the ASN. If the nonce used in the Layer 2 security derives from the extended (MAC-64) address, then replaying the ASN alone cannot enable a nonce-reuse attack unless the same node has lost its state with a previous ASN. But if the nonce derives from the short address (e.g., assigned by the JRC), then the JRC must ensure that it never assigns short addresses that were already given to this or other nodes with the same keys. In other words, the network must be rekeyed before the JRC runs out of short addresses.

Network Keying and Rekeying provides an overview of the CoJP process described in by which an LLN can be assembled in the field, having been provisioned in a lab. is future work that precedes and then leverages CoJP using the constrained profile of . This later work requires a yet-to-be standardized Lightweight Authenticated Key Exchange protocol. CoJP results in distribution of a network-wide key that is to be used with security. The details of use are described in , Sections and . The BRSKI mechanism may lead to the use of CoJP, in which case it also results in distribution of a network-wide key. Alternatively the BRSKI mechanism may be followed by use of to enroll certificates for each device. In that case, the certificates may be used with an key agreement protocol. The description of this mechanism, while conceptually straightforward, still has significant standardization hurdles to pass. describes a mechanism to change (rekey) the network. There are a number of reasons to initiate a network rekey: to remove unwanted (corrupt/malicious) nodes, to recover unused 2-byte short addresses, or due to limits in encryption algorithms. For all of the mechanisms that distribute a network-wide key, rekeying is also needed on a periodic basis. In more detail:

• The mechanism described in requires advance communication between the JRC and every one of the nodes before the key change. Given that many nodes may be sleepy, this operation may take a significant amount of time and may consume a significant portion of the available bandwidth. As such, network-wide rekeys to exclude nodes that have become malicious will not be particularly quick. If a rekey is already in progress, but the unwanted node has not yet been updated, then it is possible to just continue the operation. If the unwanted node has already received the update, then the rekey operation will need to be restarted.
• The cryptographic mechanisms used by IEEE Std 802.15.4 include the 2-byte short address in the calculation of the context. A nonce-reuse attack may become feasible if a short address is reassigned to another node while the same network-wide keys are in operation. A network that gains and loses nodes on a regular basis is likely to reach the 65536 limit of the 2-byte (16-bit) short addresses, even if the network has only a few thousand nodes. Network planners should consider the need to rekey the network on a periodic basis in order to recover 2-byte addresses. The rekey can update the short addresses for active nodes if desired, but there is actually no need to do this as long as the key has been changed.
• With TSCH as it stands at the time of this writing, the ASN will wrap after 2^40 timeslot durations, meaning around 350 years with the default values. Wrapping ASN is not expected to happen within the lifetime of most LLNs. Yet, should the ASN wrap, the network must be rekeyed to avoid a nonce-reuse attack.
• Many cipher algorithms have some suggested limits on how many bytes should be encrypted with that algorithm before a new key is used. These numbers are typically in the many to hundreds of gigabytes of data. On very fast backbone networks, this becomes an important concern. On LLNs with typical data rates in the kilobits/second, this concern is significantly less. With IEEE Std 802.15.4 as it stands at the time of this writing, the ASN will wrap before the limits of the current L2 crypto (AES-CCM-128) are reached, so the problem should never occur.
• In any fashion, if the LLN is expected to operate continuously for decades, then the operators are advised to plan for the need to rekey.

Except for urgent rekeys caused by malicious nodes, the rekey operation described in can be done as a background task and can be done incrementally. It is a make-before-break mechanism. The switch over to the new key is not signaled by time, but rather by observation that the new key is in use. As such, the update can take as long as needed, or occur in as short a time as practical.

References Normative References This document specifies the Neighbor Discovery protocol for IP Version 6. IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence, to determine each other's link-layer addresses, to find routers, and to maintain reachability information about the paths to active neighbors. [STANDARDS-TRACK] This document specifies the steps a host takes in deciding how to autoconfigure its interfaces in IP version 6. The autoconfiguration process includes generating a link-local address, generating global addresses via stateless address autoconfiguration, and the Duplicate Address Detection procedure to verify the uniqueness of the addresses on a link. [STANDARDS-TRACK] This document describes the frame format for transmission of IPv6 packets and the method of forming IPv6 link-local addresses and statelessly autoconfigured addresses on IEEE 802.15.4 networks. Additional specifications include a simple header compression scheme using shared context and provisions for packet delivery in IEEE 802.15.4 meshes. [STANDARDS-TRACK] This document describes a model for configuring IP addresses and subnet prefixes on the interfaces of routers which connect to links with undetermined connectivity properties. This document is not an Internet Standards Track specification; it is published for informational purposes. This document updates RFC 4944, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks". This document specifies an IPv6 header compression format for IPv6 packet delivery in Low Power Wireless Personal Area Networks (6LoWPANs). The compression format relies on shared context to allow compression of arbitrary prefixes. How the information is maintained in that shared context is out of scope. This document specifies compression of multicast addresses and a framework for compressing next headers. UDP header compression is specified within this framework. [STANDARDS-TRACK] Low-Power and Lossy Networks (LLNs) are a class of network in which both the routers and their interconnect are constrained. LLN routers typically operate with constraints on processing power, memory, and energy (battery power). Their interconnects are characterized by high loss rates, low data rates, and instability. LLNs are comprised of anything from a few dozen to thousands of routers. Supported traffic flows include point-to-point (between devices inside the LLN), point-to-multipoint (from a central control point to a subset of devices inside the LLN), and multipoint-to-point (from devices inside the LLN towards a central control point). This document specifies the IPv6 Routing Protocol for Low-Power and Lossy Networks (RPL), which provides a mechanism whereby multipoint-to-point traffic from devices inside the LLN towards a central control point as well as point-to-multipoint traffic from the central control point to the devices inside the LLN are supported. Support for point-to-point traffic is also available. [STANDARDS-TRACK] Low-Power and Lossy Networks (LLNs) have unique characteristics compared with traditional wired and ad hoc networks that require the specification of new routing metrics and constraints. By contrast, with typical Interior Gateway Protocol (IGP) routing metrics using hop counts or link metrics, this document specifies a set of link and node routing metrics and constraints suitable to LLNs to be used by the Routing Protocol for Low-Power and Lossy Networks (RPL). [STANDARDS-TRACK] The Routing Protocol for Low-Power and Lossy Networks (RPL) specification defines a generic Distance Vector protocol that is adapted to a variety of network types by the application of specific Objective Functions (OFs). An OF states the outcome of the process used by a RPL node to select and optimize routes within a RPL Instance based on the Information Objects available; an OF is not an algorithm. This document specifies a basic Objective Function that relies only on the objects that are defined in the RPL and does not use any protocol extensions. [STANDARDS-TRACK] The Routing Protocol for Low-Power and Lossy Networks (RPL) includes routing information in data-plane datagrams to quickly identify inconsistencies in the routing topology. This document describes the RPL Option for use among RPL routers to include such routing information. [STANDARDS-TRACK] In Low-Power and Lossy Networks (LLNs), memory constraints on routers may limit them to maintaining, at most, a few routes. In some configurations, it is necessary to use these memory-constrained routers to deliver datagrams to nodes within the LLN. The Routing Protocol for Low-Power and Lossy Networks (RPL) can be used in some deployments to store most, if not all, routes on one (e.g., the Directed Acyclic Graph (DAG) root) or a few routers and forward the IPv6 datagram using a source routing technique to avoid large routing tables on memory-constrained routers. This document specifies a new IPv6 Routing header type for delivering datagrams within a RPL routing domain. [STANDARDS-TRACK] The IETF work in IPv6 over Low-power Wireless Personal Area Network (6LoWPAN) defines 6LoWPANs such as IEEE 802.15.4. This and other similar link technologies have limited or no usage of multicast signaling due to energy conservation. In addition, the wireless network may not strictly follow the traditional concept of IP subnets and IP links. IPv6 Neighbor Discovery was not designed for non- transitive wireless links, as its reliance on the traditional IPv6 link concept and its heavy use of multicast make it inefficient and sometimes impractical in a low-power and lossy network. This document describes simple optimizations to IPv6 Neighbor Discovery, its addressing mechanisms, and duplicate address detection for Low- power Wireless Personal Area Networks and similar networks. The document thus updates RFC 4944 to specify the use of the optimizations defined here. [STANDARDS-TRACK] This document provides a glossary of terminology used in routing requirements and solutions for networks referred to as Low-Power and Lossy Networks (LLNs). An LLN is typically composed of many embedded devices with limited power, memory, and processing resources interconnected by a variety of links. There is a wide scope of application areas for LLNs, including industrial monitoring, building automation (e.g., heating, ventilation, air conditioning, lighting, access control, fire), connected home, health care, environmental monitoring, urban sensor networks, energy management, assets tracking, and refrigeration. The Internet Protocol Suite is increasingly used on small devices with severe constraints on power, memory, and processing resources, creating constrained-node networks. This document provides a number of basic terms that have been useful in the standardization work for constrained-node networks. The Constrained Application Protocol (CoAP) is a specialized web transfer protocol for use with constrained nodes and constrained (e.g., low-power, lossy) networks. The nodes often have 8-bit microcontrollers with small amounts of ROM and RAM, while constrained networks such as IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs) often have high packet error rates and a typical throughput of 10s of kbit/s. The protocol is designed for machine- to-machine (M2M) applications such as smart energy and building automation. CoAP provides a request/response interaction model between application endpoints, supports built-in discovery of services and resources, and includes key concepts of the Web such as URIs and Internet media types. CoAP is designed to easily interface with HTTP for integration with the Web while meeting specialized requirements such as multicast support, very low overhead, and simplicity for constrained environments. This document describes the environment, problem statement, and goals for using the Time-Slotted Channel Hopping (TSCH) Medium Access Control (MAC) protocol of IEEE 802.14.4e in the context of Low-Power and Lossy Networks (LLNs). The set of goals enumerated in this document form an initial set only. This specification updates RFC 4944 to introduce a new context switch mechanism for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) compression, expressed in terms of Pages and signaled by a new Paging Dispatch. IEEE Std 802.15.4 defines Information Elements (IEs) that can be used to extend 802.15.4 in an interoperable manner. The IEEE 802.15 Assigned Numbers Authority (ANA) manages the registry of the Information Elements. This document formulates a request for ANA to allocate a number from that registry for the IETF and describes how the IE is formatted to provide subtypes. This specification introduces a new IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) dispatch type for use in 6LoWPAN route-over topologies, which initially covers the needs of Routing Protocol for Low-Power and Lossy Networks (RPL) data packet compression (RFC 6550). Using this dispatch type, this specification defines a method to compress the RPL Option (RFC 6553) information and Routing Header type 3 (RFC 6554), an efficient IP-in-IP technique, and is extensible for more applications. This document describes a minimal mode of operation for an IPv6 over the TSCH mode of IEEE 802.15.4e (6TiSCH) network. This minimal mode of operation specifies the baseline set of protocols that need to be supported and the recommended configurations and modes of operation sufficient to enable a 6TiSCH functional network. 6TiSCH provides IPv6 connectivity over a Time-Slotted Channel Hopping (TSCH) mesh composed of IEEE Std 802.15.4 TSCH links. This minimal mode uses a collection of protocols with the respective configurations, including the IPv6 Low-Power Wireless Personal Area Network (6LoWPAN) framework, enabling interoperable IPv6 connectivity over IEEE Std 802.15.4 TSCH. This minimal configuration provides the necessary bandwidth for network and security bootstrapping and defines the proper link between the IETF protocols that interface to IEEE Std 802.15.4 TSCH. This minimal mode of operation should be implemented by all 6TiSCH-compliant devices. This document specifies version 6 of the Internet Protocol (IPv6). It obsoletes RFC 2460. Traffic Engineered (TE) networks have a variety of mechanisms to facilitate the separation of the data plane and control plane. They also have a range of management and provisioning protocols to configure and activate network resources. These mechanisms represent key technologies for enabling flexible and dynamic networking. The term "Traffic Engineered network" refers to a network that uses any connection-oriented technology under the control of a distributed or centralized control plane to support dynamic provisioning of end-to- end connectivity. Abstraction of network resources is a technique that can be applied to a single network domain or across multiple domains to create a single virtualized network that is under the control of a network operator or the customer of the operator that actually owns the network resources. This document provides a framework for Abstraction and Control of TE Networks (ACTN) to support virtual network services and connectivity services. This document defines the "IPv6 over the TSCH mode of IEEE 802.15.4e" (6TiSCH) Operation Sublayer (6top) Protocol (6P), which enables distributed scheduling in 6TiSCH networks. 6P allows neighbor nodes to add/delete Time-Slotted Channel Hopping (TSCH) cells to/on one another. 6P is part of the 6TiSCH Operation Sublayer (6top), the layer just above the IEEE Std 802.15.4 TSCH Medium Access Control layer. 6top is composed of one or more Scheduling Functions (SFs) and the 6top Protocol defined in this document. A 6top SF decides when to add/delete cells, and it triggers 6P Transactions. The definition of SFs is out of scope for this document; however, this document provides the requirements for an SF. This specification updates RFC 6775 -- the Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery specification -- to clarify the role of the protocol as a registration technique and simplify the registration operation in 6LoWPAN routers, as well as to provide enhancements to the registration capabilities and mobility detection for different network topologies, including the Routing Registrars performing routing for host routes and/or proxy Neighbor Discovery in a low-power network. This document provides the overall architecture for Deterministic Networking (DetNet), which provides a capability to carry specified unicast or multicast data flows for real-time applications with extremely low data loss rates and bounded latency within a network domain. Techniques used include 1) reserving data-plane resources for individual (or aggregated) DetNet flows in some or all of the intermediate nodes along the path of the flow, 2) providing explicit routes for DetNet flows that do not immediately change with the network topology, and 3) distributing data from DetNet flow packets over time and/or space to ensure delivery of each packet's data in spite of the loss of a path. DetNet operates at the IP layer and delivers service over lower-layer technologies such as MPLS and Time- Sensitive Networking (TSN) as defined by IEEE 802.1. This document updates the IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery (ND) protocol defined in RFCs 6775 and 8505. The new extension is called Address-Protected Neighbor Discovery (AP-ND), and it protects the owner of an address against address theft and impersonation attacks in a Low-Power and Lossy Network (LLN). Nodes supporting this extension compute a cryptographic identifier (Crypto-ID), and use it with one or more of their Registered Addresses. The Crypto-ID identifies the owner of the Registered Address and can be used to provide proof of ownership of the Registered Addresses. Once an address is registered with the Crypto-ID and a proof of ownership is provided, only the owner of that address can modify the registration information, thereby enforcing Source Address Validation. This document updates RFCs 6775 and 8505 in order to enable proxy services for IPv6 Neighbor Discovery by Routing Registrars called "Backbone Routers". Backbone Routers are placed along the wireless edge of a backbone and federate multiple wireless links to form a single Multi-Link Subnet (MLSN). This document provides generic rules to enable the forwarding of an IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) fragment over a route-over network. Forwarding fragments can improve both end-to-end latency and reliability as well as reduce the buffer requirements in intermediate nodes; it may be implemented using RFC 4944 and Virtual Reassembly Buffers (VRBs). This document updates RFC 4944 with a protocol that forwards individual fragments across a route-over mesh and recovers them end to end, with congestion control capabilities to protect the network. This document looks at different data flows through Low-Power and Lossy Networks (LLN) where RPL (IPv6 Routing Protocol for Low-Power and Lossy Networks) is used to establish routing. The document enumerates the cases where RPL Packet Information (RPI) Option Type (RFC 6553), RPL Source Route Header (RFC 6554), and IPv6-in-IPv6 encapsulation are required in the data plane. This analysis provides the basis upon which to design efficient compression of these headers. This document updates RFC 6553 by adding a change to the RPI Option Type. Additionally, this document updates RFC 6550 by defining a flag in the DODAG Information Object (DIO) Configuration option to indicate this change and updates RFC 8138 as well to consider the new Option Type when the RPL Option is decompressed. This specification provides a mechanism for a host that implements a routing-agnostic interface based on IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery to obtain reachability services across a network that leverages RFC 6550 for its routing operations. It updates RFCs 6550, 6775, and 8505. Informative References U.S. Department of Energy IETF SRM University-AP Huawei Technologies Lupin Lodge Indian Institute of Science Huawei Technologies Route discovery for symmetric and asymmetric Point-to-Point (P2P) traffic flows is a desirable feature in Low power and Lossy Networks (LLNs). For that purpose, this document specifies a reactive P2P route discovery mechanism for both hop-by-hop routing and source routing: Ad Hoc On-demand Distance Vector Routing (AODV) based RPL protocol (AODV-RPL). Paired Instances are used to construct directional paths, in case some of the links between source and target node are asymmetric. Work in Progress The Ad Hoc On-demand Distance Vector Version 2 (AODVv2) routing protocol is intended for use by mobile routers in wireless, multihop networks. AODVv2 determines unicast routes among AODVv2 routers within the network in an on-demand fashion. Work in Progress Work in Progress IETF IEEE Work in Progress Cisco Systems, Inc Huawei Tech Itron, Inc This document extends RFC 6550 and RFC 6553 to enable a RPL Root to install and maintain Projected Routes within its DODAG, along a selected set of nodes that may or may not include self, for a chosen duration. This potentially enables routes that are more optimized or resilient than those obtained with the classical distributed operation of RPL, either in terms of the size of a Routing Header or in terms of path length, which impacts both the latency and the packet delivery ratio. Work in Progress Ericsson AB Ericsson AB Ericsson AB This document specifies Ephemeral Diffie-Hellman Over COSE (EDHOC), a very compact, and lightweight authenticated Diffie-Hellman key exchange with ephemeral keys. EDHOC provides mutual authentication, perfect forward secrecy, and identity protection. EDHOC is intended for usage in constrained scenarios and a main use case is to establish an OSCORE security context. By reusing COSE for cryptography, CBOR for encoding, and CoAP for transport, the additional code footprint can be kept very low. Work in Progress Work in Progress FieldComm Group IEC IEEE IEEE ISA/ANSI ISA/ANSI Work in Progress IETF Work in Progress IMT Atlantique Cisco CNRS UC3M The wireless medium presents significant specific challenges to achieve properties similar to those of wired deterministic networks. At the same time, a number of use cases cannot be solved with wires and justify the extra effort of going wireless. This document presents wireless use cases demanding reliable and available behavior. Work in Progress This document defines the IP header field, called the DS (for differentiated services) field. [STANDARDS-TRACK] BGP-4 Multiprotocol Extensions (BGP-MP) defines the format of two BGP attributes (MP_REACH_NLRI and MP_UNREACH_NLRI) that can be used to announce and withdraw the announcement of reachability information. This document defines how compliant systems should make use of those attributes for the purpose of conveying IPv6 routing information. [STANDARDS-TRACK] This document describes the use of RSVP (Resource Reservation Protocol), including all the necessary extensions, to establish label-switched paths (LSPs) in MPLS (Multi-Protocol Label Switching). Since the flow along an LSP is completely identified by the label applied at the ingress node of the path, these paths may be treated as tunnels. A key application of LSP tunnels is traffic engineering with MPLS as specified in RFC 2702. [STANDARDS-TRACK] There has been ongoing confusion about the differences between Information Models and Data Models for defining managed objects in network management. This document explains the differences between these terms by analyzing how existing network management model specifications (from the IETF and other bodies such as the International Telecommunication Union (ITU) or the Distributed Management Task Force (DMTF)) fit into the universe of Information Models and Data Models. This memo documents the main results of the 8th workshop of the Network Management Research Group (NMRG) of the Internet Research Task Force (IRTF) hosted by the University of Texas at Austin. This memo provides information for the Internet community. This document describes the Network Mobility (NEMO) Basic Support protocol that enables Mobile Networks to attach to different points in the Internet. The protocol is an extension of Mobile IPv6 and allows session continuity for every node in the Mobile Network as the network moves. It also allows every node in the Mobile Network to be reachable while moving around. The Mobile Router, which connects the network to the Internet, runs the NEMO Basic Support protocol with its Home Agent. The protocol is designed so that network mobility is transparent to the nodes inside the Mobile Network. [STANDARDS-TRACK] The Next Steps in Signaling (NSIS) working group is considering protocols for signaling information about a data flow along its path in the network. The NSIS suite of protocols is envisioned to support various signaling applications that need to install and/or manipulate such state in the network. Based on existing work on signaling requirements, this document proposes an architectural framework for these signaling protocols. This document provides a model for the network entities that take part in such signaling, and for the relationship between signaling and the rest of network operation. We decompose the overall signaling protocol suite into a generic (lower) layer, with separate upper layers for each specific signaling application. This memo provides information for the Internet community. This specification defines the addressing architecture of the IP Version 6 (IPv6) protocol. The document includes the IPv6 addressing model, text representations of IPv6 addresses, definition of IPv6 unicast addresses, anycast addresses, and multicast addresses, and an IPv6 node's required addresses. This document obsoletes RFC 3513, "IP Version 6 Addressing Architecture". [STANDARDS-TRACK] There have been several proposals around the notion that a subnet may span multiple links connected by routers. This memo documents the issues and potential problems that have been raised with such an approach. This memo provides information for the Internet community. This document describes the assumptions, problem statement, and goals for transmitting IP over IEEE 802.15.4 networks. The set of goals enumerated in this document form an initial set only. This memo provides information for the Internet community. This document describes the modifications to OSPF to support version 6 of the Internet Protocol (IPv6). The fundamental mechanisms of OSPF (flooding, Designated Router (DR) election, area support, Short Path First (SPF) calculations, etc.) remain unchanged. However, some changes have been necessary, either due to changes in protocol semantics between IPv4 and IPv6, or simply to handle the increased address size of IPv6. These modifications will necessitate incrementing the protocol version from version 2 to version 3. OSPF for IPv6 is also referred to as OSPF version 3 (OSPFv3). Changes between OSPF for IPv4, OSPF Version 2, and OSPF for IPv6 as described herein include the following. Addressing semantics have been removed from OSPF packets and the basic Link State Advertisements (LSAs). New LSAs have been created to carry IPv6 addresses and prefixes. OSPF now runs on a per-link basis rather than on a per-IP-subnet basis. Flooding scope for LSAs has been generalized. Authentication has been removed from the OSPF protocol and instead relies on IPv6's Authentication Header and Encapsulating Security Payload (ESP). Even with larger IPv6 addresses, most packets in OSPF for IPv6 are almost as compact as those in OSPF for IPv4. Most fields and packet- size limitations present in OSPF for IPv4 have been relaxed. In addition, option handling has been made more flexible. All of OSPF for IPv4's optional capabilities, including demand circuit support and Not-So-Stubby Areas (NSSAs), are also supported in OSPF for IPv6. [STANDARDS-TRACK] This specification describes the NSIS Signaling Layer Protocol (NSLP) for signaling Quality of Service (QoS) reservations in the Internet. It is in accordance with the framework and requirements developed in NSIS. Together with General Internet Signaling Transport (GIST), it provides functionality similar to RSVP and extends it. The QoS NSLP is independent of the underlying QoS specification or architecture and provides support for different reservation models. It is simplified by the elimination of support for multicast flows. This specification explains the overall protocol approach, describes the design decisions made, and provides examples. It specifies object, message formats, and processing rules. This document defines an Experimental Protocol for the Internet community. This document specifies Mobile IPv6, a protocol that allows nodes to remain reachable while moving around in the IPv6 Internet. Each mobile node is always identified by its home address, regardless of its current point of attachment to the Internet. While situated away from its home, a mobile node is also associated with a care-of address, which provides information about the mobile node's current location. IPv6 packets addressed to a mobile node's home address are transparently routed to its care-of address. The protocol enables IPv6 nodes to cache the binding of a mobile node's home address with its care-of address, and to then send any packets destined for the mobile node directly to it at this care-of address. To support this operation, Mobile IPv6 defines a new IPv6 protocol and a new destination option. All IPv6 nodes, whether mobile or stationary, can communicate with mobile nodes. This document obsoletes RFC 3775. [STANDARDS-TRACK] This document specifies version 1.2 of the Datagram Transport Layer Security (DTLS) protocol. The DTLS protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. The DTLS protocol is based on the Transport Layer Security (TLS) protocol and provides equivalent security guarantees. Datagram semantics of the underlying transport are preserved by the DTLS protocol. This document updates DTLS 1.0 to work with TLS version 1.2. [STANDARDS-TRACK] IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs) are formed by devices that are compatible with the IEEE 802.15.4 standard. However, neither the IEEE 802.15.4 standard nor the 6LoWPAN format specification defines how mesh topologies could be obtained and maintained. Thus, it should be considered how 6LoWPAN formation and multi-hop routing could be supported. This document provides the problem statement and design space for 6LoWPAN routing. It defines the routing requirements for 6LoWPANs, considering the low-power and other particular characteristics of the devices and links. The purpose of this document is not to recommend specific solutions but to provide general, layer-agnostic guidelines about the design of 6LoWPAN routing that can lead to further analysis and protocol design. This document is intended as input to groups working on routing protocols relevant to 6LoWPANs, such as the IETF ROLL WG. This document is not an Internet Standards Track specification; it is published for informational purposes. This document describes a network-layer-based protocol that enables separation of IP addresses into two new numbering spaces: Endpoint Identifiers (EIDs) and Routing Locators (RLOCs). No changes are required to either host protocol stacks or to the "core" of the Internet infrastructure. The Locator/ID Separation Protocol (LISP) can be incrementally deployed, without a "flag day", and offers Traffic Engineering, multihoming, and mobility benefits to early adopters, even when there are relatively few LISP-capable sites. Design and development of LISP was largely motivated by the problem statement produced by the October 2006 IAB Routing and Addressing Workshop. This document defines an Experimental Protocol for the Internet community. Software-Defined Networking (SDN) refers to a new approach for network programmability, that is, the capacity to initialize, control, change, and manage network behavior dynamically via open interfaces. SDN emphasizes the role of software in running networks through the introduction of an abstraction for the data forwarding plane and, by doing so, separates it from the control plane. This separation allows faster innovation cycles at both planes as experience has already shown. However, there is increasing confusion as to what exactly SDN is, what the layer structure is in an SDN architecture, and how layers interface with each other. This document, a product of the IRTF Software-Defined Networking Research Group (SDNRG), addresses these questions and provides a concise reference for the SDN research community based on relevant peer-reviewed literature, the RFC series, and relevant documents by other standards organizations. This document presents use cases for diverse industries that have in common a need for "deterministic flows". "Deterministic" in this context means that such flows provide guaranteed bandwidth, bounded latency, and other properties germane to the transport of time-sensitive data. These use cases differ notably in their network topologies and specific desired behavior, providing as a group broad industry context for Deterministic Networking (DetNet). For each use case, this document will identify the use case, identify representative solutions used today, and describe potential improvements that DetNet can enable. This document defines Object Security for Constrained RESTful Environments (OSCORE), a method for application-layer protection of the Constrained Application Protocol (CoAP), using CBOR Object Signing and Encryption (COSE). OSCORE provides end-to-end protection between endpoints communicating using CoAP or CoAP-mappable HTTP. OSCORE is designed for constrained nodes and networks supporting a range of proxy operations, including translation between different transport protocols. Although an optional functionality of CoAP, OSCORE alters CoAP options processing and IANA registration. Therefore, this document updates RFC 7252. This document specifies the Deterministic Networking (DetNet) data plane operation for IP hosts and routers that provide DetNet service to IP-encapsulated data. No DetNet-specific encapsulation is defined to support IP flows; instead, the existing IP-layer and higher-layer protocol header information is used to support flow identification and DetNet service delivery. This document builds on the DetNet architecture (RFC 8655) and data plane framework (RFC 8938). This document specifies automated bootstrapping of an Autonomic Control Plane. To do this, a Secure Key Infrastructure is bootstrapped. This is done using manufacturer-installed X.509 certificates, in combination with a manufacturer's authorizing service, both online and offline. We call this process the Bootstrapping Remote Secure Key Infrastructure (BRSKI) protocol. Bootstrapping a new device can occur when using a routable address and a cloud service, only link-local connectivity, or limited/disconnected networks. Support for deployment models with less stringent security requirements is included. Bootstrapping is complete when the cryptographic identity of the new key infrastructure is successfully deployed to the device. The established secure connection can be used to deploy a locally issued certificate to the device as well. This document updates RFC 8138 by defining a bit in the Routing Protocol for Low-Power and Lossy Networks (RPL) Destination-Oriented Directed Acyclic Graph (DODAG) Configuration option to indicate whether compression is used within the RPL Instance and to specify the behavior of nodes compliant with RFC 8138 when the bit is set and unset. RISE AB Yanzi Networks AB University of Pisa This document defines a method to generate robust TSCH schedules in a 6TiSCH (IPv6 over the TSCH mode of IEEE 802.15.4-2015) network, so as to protect network nodes against selective jamming attack. Network nodes independently compute the new schedule at each slotframe, by altering the one originally available from 6top or alternative protocols, while preserving a consistent and collision-free communication pattern. This method can be added on top of the minimal security framework for 6TiSCH. Work in Progress Work in Progress Work in Progress Cisco Systems, Inc Sandelman Software Works Juniper Work in Progress ACM SIGCOMM Computer Communication Review Work in Progress IETF Universitaet Bremen TZI Analog Devices When employing adaptation layer fragmentation in 6LoWPAN, it may be beneficial for a forwarder not to have to reassemble each packet in its entirety before forwarding it. This has been always possible with the original fragmentation design of RFC 4944. Apart from a brief mention of the way to do this in Section 2.5.2 of the 6LoWPAN book, this has not been extensively described in the literature. The present document attempts to fill that gap. Work in Progress International Electrotechnical Commission Sandelman Software Works This document describes a Zero-touch Secure Join (ZSJ) mechanism to enroll a new device (the "pledge") into a IEEE802.15.4 TSCH network using the 6tisch signaling mechanisms. The resulting device will obtain a domain specific credential that can be used with either 802.15.9 per-host pair keying protocols, or to obtain the network- wide key from a coordinator. The mechanism describe here is an augmentation to the one-touch mechanism described in [I-D.ietf-6tisch-minimal-security], and is a profile of the constrained voucher mechanism [I-D.ietf-anima-constrained-voucher]. Work in Progress

Related Work in Progress This document has been incremented as the work progressed following the evolution of the WG charter and the availability of dependent work. The intent was to publish when the WG concluded on the covered items. At the time of publishing, the following specifications are still in progress and may affect the evolution of the stack in a 6TiSCH-aware node.

Unchartered IETF Work Items

6TiSCH Zero-Touch Security The security model and in particular the zero-touch join process depend on the ANIMA (Autonomic Networking Integrated Model and Approach) "" to enable zero-touch security provisioning; for highly constrained nodes, a minimal model based on pre-shared keys (PSK) is also available. As currently written, it also depends on a number of documents in progress in the CORE (Constrained RESTful Environments) WG and on "Ephemeral Diffie-Hellman Over COSE (EDHOC)", which is being considered for adoption by the LAKE (Lightweight Authenticated Key Exchange) WG.

6TiSCH Track Setup ROLL (Routing Over Low power and Lossy networks) is now standardizing a reactive routing protocol based on RPL . The need of a reactive routing protocol to establish on-demand, constraint-optimized routes and a reservation protocol to establish Layer 3 Tracks is being discussed in 6TiSCH but not yet chartered. At the time of this writing, there is new work planned in the IETF to provide limited deterministic networking capabilities for wireless networks with a focus on forwarding behaviors to react quickly and locally to the changes as described in . ROLL is also standardizing an extension to RPL to set up centrally computed routes . The 6TiSCH architecture should thus inherit from the DetNet architecture and thus depends on it. The PCE should be a core component of that architecture. An extension to RPL or to TEAS (Traffic Engineering Architecture and Signaling) will be required to expose the 6TiSCH node capabilities and the network peers to the PCE, possibly in combination with . A protocol such as a lightweight Path Computation Element Communication Protocol (PCEP) or an adaptation of Common Control and Measurement Plane (CCAMP) GMPLS formats and procedures could be used in combination to to install the Tracks, as computed by the PCE, to the 6TiSCH nodes.

Using BIER in a 6TiSCH Network ROLL is actively working on Bit Index Explicit Replication (BIER) as a method to compress both the data-plane packets and the routing tables in storing mode . BIER could also be used in the context of the DetNet service layer. "BIER-TE extensions for Packet Replication and Elimination Function (PREF) and OAM" leverages BIER Traffic Engineering (TE) to control the DetNet Replication and Elimination activities in the data plane, and to provide traceability on links where replication and loss happen, in a manner that is abstract to the forwarding information. "A 6loRH for BitStrings" proposes a 6LoWPAN compression for the BIER BitString based on 6LoWPAN Routing Header.

External (Non-IETF) Work Items The current charter positions 6TiSCH on IEEE Std 802.15.4 only. Though most of the design should be portable to other link types, 6TiSCH has a strong dependency on IEEE Std 802.15.4 and its evolution. The impact of changes to TSCH on this architecture should be minimal to nonexistent, but deeper work such as 6top and security may be impacted. A 6TiSCH Interest Group at the IEEE maintains the synchronization and helps foster work at the IEEE should 6TiSCH demand it. Work is being proposed at IEEE (802.15.12 PAR) for an LLC that would logically include the 6top sublayer. The interaction with the 6top sublayer and the Scheduling Functions described in this document are yet to be defined. ISA100 Common Network Management (CNM) is another external work of interest for 6TiSCH. The group, referred to as ISA100.20, defines a Common Network Management framework that should enable the management of resources that are controlled by heterogeneous protocols such as ISA100.11a , WirelessHART , and 6TiSCH. Interestingly, the establishment of 6TiSCH deterministic paths, called Tracks, are also in scope, and ISA100.20 is working on requirements for DetNet.

Acknowledgments

Special Thanks Special thanks to , , , and for their deep contributions to the initial security work, to for his work on implementation and simulation that tremendously helped build a robust system, to for starting and leading the SF0 effort, and to for evolving it in the MSF. Special thanks also to , , and for their support in maintaining the connection active and the design in line with work happening at IEEE 802.15. Special thanks to , who was the INT Area Director while this document was initiated, for his great support and help throughout, and to , who took over with that kind efficiency of his till publication. Also special thanks to , who performed the first INT Area Directorate review, which was very deep and thorough and radically changed the orientations of this document, and then to and , who helped finalize this document in preparation for the IESG reviews, and to , , , , , , , , and , who contributed to the final shaping of this document through the IESG review procedure.

And Do Not Forget This document is the result of multiple interactions, in particular during the 6TiSCH (bi)Weekly Interim call, relayed through the 6TiSCH mailing list at the IETF, over the course of more than 5 years. The authors wish to thank in arbitrary order: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , and for their participation and various contributions.

Contributors The co-authors of this document are listed below:

• for his contributions to the whole design, in particular on TSCH and security, and to the open source community that he created with openWSN;
• , who led the design of the minimal support with RPL and contributed deeply to the 6top design and the GMPLS operation of Track switching;
• for creating TSCH and his continuing guidance through the elaboration of this design;
• for the work on the one-touch join process and his contribution to the Security Design Team;
• for his leadership role in the Security Design Team and his contribution throughout this document;
• for his contribution to the security work in general and the security section in particular;
• for managing the Terminology document that was merged into this document through the work of 6TiSCH;
• for his contribution to the open source community with the 6TiSCH implementation of contiki, and for his contribution to MSF and autonomous unicast cells;
• , who led the design of the 6top sublayer and contributed related text that was moved and/or adapted into this document;
• for the security section and his contribution to the Security Design Team;
• for his breakthrough work on RPL over TSCH and initial text and guidance.

Author's Address Cisco Systems, Inc

Building D 45 Allee des Ormes - BP1200 Mougins - Sophia Antipolis 06254 France +33 497 23 26 34 [email protected]