This repo contains libhal compatible libraries for numerous ARM Cortex-M processor microcontrollers (MCUs). This is a platform library supporting generic ARM processor APIs and peripheral drivers from many different microcontrollers.

To learn about the available drivers and APIs see the headers include/libhal-arm-mcu directory.

To see how each driver is used see the demos/ directory.

Fully rendered Doxygen APIs will be provided when issue#37 is closed.

To get started with libhal, follow the 🚀 Getting Started guide.

Profiles define which platform you mean to build your project against. These profiles are needed for code and demos in this repo and for applications that wish to execute on an arm mcu supported by this library. The following will install the conan profiles for arm mcus and the compiler.

conan config install -sf conan/profiles/v1 -tf profiles https://github.com/libhal/arm-gnu-toolchain.git
conan config install -sf conan/profiles/v1 -tf profiles https://github.com/libhal/libhal-arm-mcu.git

Note that running these commands multiple times is safe. The command will simply overwrite the old files with the latest files.

To build demos, start at the root of the repo and execute the following command:

conan build demos -pr lpc4078 -s build_type=Debug

This will build the demos for the lpc4078 microcontroller in Debug mode. Replace lpc4078 with any of the other complete profiles found in the ./conan/profiles/v1/. Incomplete profiles do not match an exact device such as lpc40 or stm32f1.

There are a few ways to flash an LPC40 series MCU. The recommended methods are via USB or using a debugger JTAG/SWD.

nxpprog is a script for programming and flashing LPC40 series chips over serial/UART. Using it will require a USB to serial/uart adaptor.

See the README on nxpprog, for details on how to use NXPPROG.

To install nxpprog:

python3 -m pip install -U nxpprog

To flash command is:

nxpprog --control --binary demos/lpc4078/blinker.elf.bin --device /dev/tty.usbserial-10

• Replace demos/lpc4078/blinker.elf.bin with the path to the binary you'd like to flash.
• Replace /dev/tty.usbserial-10 with the path to your serial port on your machine.

stm32loader is a script for programming and flashing LPC40 series chips over serial/UART. Using it will require a USB to serial/uart adaptor.

For more information, please refer to the README of stm32loader.

To install stm32loader:

python3 -m pip install stm32loader

To flash command is:

stm32loader -p /dev/tty.usbserial-10 -e -w -v demos/build/stm32f103c8/Debug/blinker.elf.bin

• Replace demos/build/stm32f103c8/Debug/blinker.elf.bin with the path to the binary you'd like to flash.
• Replace /dev/tty.usbserial-10 with the path to your serial port on your machine.

PyOCD is a debugging interface for programming and also debugging ARM Cortex M processor devices over JTAG and SWD.

This will require a JTAG or SWD debugger. The recommended debugger for the LPC40 series of devices is the STLink v2 (cheap variants can be found on Amazon).

See PyOCD Installation Page for installation details.

For reference the flashing command is:

pyocd flash --target lpc4088 demos/build/lpc4078/Debug/blinker.elf.bin
pyocd flash --target stm32f103rc demos/build/stm32f103c8/Debug/blinker.elf.bin

Note that the targets for your exact part may not exist in pyocd. Because of this, it means that the bounds of the memory may not fit your device. It is up to you to make sure you do not flash a binary larger than what can fit on your device.

This section assumes you are using the libhal-starter project.

Make sure to add the following options and default options to your app's ConanFile class:

    options = {"platform": ["ANY"]}
    default_options = {"platform": "unspecified"}

Add the following to your requirements() method:

    def requirements(self):
        self.requires("libhal-arm-mcu/[^1.0.0]")

The version number can be changed to whatever is appropriate for your application. If you don't know, using the latest is usually a good choice.

The CMake from the starter project will already be ready to support the new platform library. No change needed.

To perform a test build simple run conan build as is done above with the desired target platform profile.

Startup is managed by the picolibc runtime. In terms of startup picolibc has to manage doing two things. For one, it must construct a minimal interrupt vector table with two entries. The 1st entry is the address of the top of the stack. The 2nd entry is the address of the function that will be executed on reset. picolibc sets this to its own _start function. _start does the following:

1. Sets the main stack registers
2. Write the .data section from read-only memory
3. Set the .bss section to all zeros
4. Enable FPU if present for the core architecture
5. Calls all globally constructed C++ objects
6. Calls main()

If the .data or .bss sections must initialized manually, there are functions provided:

#include <libhal-armcortex/startup.hpp>

hal::cortex_m::initialize_data_section();
hal::cortex_m::initialize_bss_section();
hal::cortex_m::initialize_floating_point_unit();

To setting the CPU clock speed to the maximum of 120MHz, include the line below, with the rest of the includes:

#include <libhal-arm-mcu/lpc40/clock.hpp>
#include <libhal-arm-mcu/stm32f1/clock.hpp>
#include <libhal-arm-mcu/stm32f4/clock.hpp>
// etc..
#include <libhal-arm-mcu/rp2040/clock.hpp>

Next run the following command but replace 12.0_MHz with the crystal oscillator frequency connected to the microcontroller. This command REQUIRES that there be a crystal oscillator attached to the microcontroller. Calling this without the oscillator will cause the device to freeze as it will attempt to use a clock that does not exist.

hal::lpc40::maximum(12.0_MHz);
hal::stm32f1::maximum(8.0_MHz);
hal::stm32f4::maximum(10.0_MHz);
// etc...
hal::rp2040::maximum(16.0_MHz);

To set the clock rate to the max speed using the internal oscillator:

hal::lpc40::maximum_speed_using_internal_oscillator();
hal::stm32f1::maximum_speed_using_internal_oscillator();
hal::stm32f4::maximum_speed_using_internal_oscillator();
// etc...
hal::rp2040::maximum_speed_using_internal_oscillator();

These APIs may not always exist for all systems, so be sure to check if the API exists.

Coming soon...

In one terminal:

pyocd gdbserver --target=lpc4088 --persist

In another terminal:

arm-none-eabi-gdb demos/build/lpc4078/blinker.elf -ex "target remote :3333"

Replace demos/build/lpc4078/blinker.elf with the path to the elf file you'd like to use for the debugging session.

Coming soon... (its more complicated)

See CONTRIBUTING.md for details.

Apache 2.0; see LICENSE for details.

The original files came from the soon to be archived repos:

• libhal/libhal-lpc40
• libhal/libhal-stm32f1
• libhal/libhal-stm32f4
• libhal/libhal-armcortex