-
-
Notifications
You must be signed in to change notification settings - Fork 5.5k
/
Copy pathgeneric-flyboard.cfg
263 lines (217 loc) · 4.79 KB
/
generic-flyboard.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
# This file contains common pin mappings for the 9 stepper motor
# "flymaker flyboard FLYF407ZG" board from creative3dprinter.com. To
# use this config, the firmware should be compiled for the STM32F407
# with a "32KiB bootloader".
# The "make flash" command does not work on the FLYBOARD. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the FLYBOARD
# with that SD card.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PB9
dir_pin: PE0
enable_pin: !PE1
microsteps: 16
rotation_distance: 40
endstop_pin: PC3
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: PB8
dir_pin: PG11
enable_pin: !PG12
microsteps: 16
rotation_distance: 40
endstop_pin: PF2
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: PA8
dir_pin: PD6
enable_pin: !PD7
microsteps: 16
rotation_distance: 8
endstop_pin: PF0
position_endstop: 0.5
position_max: 200
[extruder]
step_pin: PC7
dir_pin: PD3
enable_pin: !PD4
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PF7 # Heat0
sensor_pin: PA0 # T1 Header
sensor_type: EPCOS 100K B57560G104F
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 350
#[extruder1]
#step_pin: PC6
#dir_pin: PA15
#enable_pin: !PD0
#heater_pin: PF6 # Heat1
#sensor_pin: PC1 # T2
#...
#[extruder2]
#step_pin: PD15
#dir_pin: PG7
#enable_pin: !PG8
#heater_pin: PE6 # Heat2
#sensor_pin: PC0 # T3
#...
#[extruder3]
#step_pin: PD14
#dir_pin: PG4
#enable_pin: !PG5
#heater_pin: PE5 # Heat3
#sensor_pin: PF10 # T4
#...
#[extruder4]
#step_pin: PD13
#dir_pin: PD11
#enable_pin: !PG2
#heater_pin: PE4 # Heat4
#sensor_pin: PF5 # T5
#...
#[extruder4]
#step_pin: PD12
#dir_pin: PD8
#enable_pin: !PD9
#heater_pin: PE3 # Heat5
#sensor_pin: PF4 # T6
#...
[heater_bed]
heater_pin: PE2
sensor_pin: PF3 # T0
sensor_type: ATC Semitec 104GT-2
control: watermark
min_temp: 0
max_temp: 200
[fan]
pin: PF8
[heater_fan fan1]
pin: PF9
#[heater_fan fan2]
#pin: PA2
#[heater_fan fan3]
#pin: PA1
#[heater_fan fan4]
#pin: PE13
#[heater_fan fan5]
#pin: PB11
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: corexy
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2208 configuration
########################################
#[tmc2208 stepper_x]
#uart_pin: PG13
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 stepper_y]
#uart_pin: PG10
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 stepper_z]
#uart_pin: PD5
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2208 extruder]
#uart_pin: PD1
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder1]
#uart_pin: PA14
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder2]
#uart_pin: PG6
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder3]
#uart_pin: PG3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder4]
#uart_pin: PD10
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder5]
#uart_pin: PB12
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PG13
##diag1_pin: PC3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_y]
#cs_pin: PG10
##diag1_pin: PF2
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_z]
#cs_pin: PBD5
##diag1_pin: PF0
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2130 extruder]
#cs_pin: PD1
##diag1_pin: PE15
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder1]
#cs_pin: PA14
##diag1_pin: PE10
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder2]
#cs_pin: PG6
##diag1_pin: PC15
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder3]
#cs_pin: PG3
##diag1_pin: PC15
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder4]
#cs_pin: PD10
##diag1_pin: PC15
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder5]
#cs_pin: PB12
##diag1_pin: PC15
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# EXP1 / EXP2 (display) pins
########################################
[board_pins]
aliases:
# EXP1 header
EXP1_1=PB10, EXP1_3=PE14, EXP1_5=PE10, EXP1_7=PE8, EXP1_9=<GND>,
EXP1_2=PE15, EXP1_4=PE12, EXP1_6=PE9, EXP1_8=PE7, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_3=PC5, EXP2_5=PC4, EXP2_7=PB2, EXP2_9=<GND>,
EXP2_2=PB13, EXP2_4=PF11, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<GND>
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
# See the sample-lcd.cfg file for definitions of common LCD displays.