Welcome to the PAT-Noxim, cycle accurate Network-on-Chip(NoC) simulator.

Networks-on-Chip (NoCs) have proven to be a low-latency and highly scalable in many-core architectures. Due to the importance of scalability, designers try to optimize latency, power and temperature across the network. Therefore, developing a precise tool to calculate the aforementioned attributes is of utmost importance. Designers need to evaluate their proposed techniques in a NoC simulated environment. So, we propose PAT-Noxim to address the shortcomings in design and post-design stages. PAT-Noxim, developed based on Access-Noxim, provides an environment to simulate a NoC in power consumption, area, delay and temperature models.

PAT-Noxim utilizes a power and thermal model that takes into account the effects of both the NoC traffic and the surrounding environment. The model is highly configurable, allowing users to adjust a range of parameters and settings to reflect their specific use cases.

The results of experiments conducted using PAT-Noxim demonstrate its effectiveness in accurately modeling power consumption and thermal behavior in NoCs. The simulator can be used to identify and address potential issues related to power and thermal management in NoCs, leading to improved system performance and reliability. Overall, PAT-Noxim represents a significant step forward in the field of NoC simulation and has the potential to be a valuable tool for researchers and practitioners alike.

PAT-Noxim is developed to support several predefined and custom architectures. it can be downloaded under GPL license terms.

If you use PAT-Noxim in your research, we would appreciate the following citation in any publications to which it has contributed:

A. Norollah, D. Derafshi, H. Beitollahi and A. Patooghy, "PAT-Noxim: A Precise Power & Thermal Cycle-Accurate NoC Simulator," 2018 31st IEEE International System-on-Chip Conference (SOCC), Arlington, VA, USA, 2018, pp. 163-168. doi: 10.1109/SOCC.2018.8618491

Get in touch with me by [email protected]

PAT-Noxim works with three different simulators in harmony to cover aforementioned models:

1. Orion 3.0 measures power consumption and area of routers by using orion model. We modified this simulator to work with PAT-Noxim.
2. McPAT calculates area and power consumption of different processing elements, implemented by designer.
3. Hotspot 6.0 receives area of routers and PEs from PAT-Noxim to calculate temperature more accurately than Access-Noxim.

Change list for the latest version of PAT-Noxim:

1. Adding virtual channels
2. Implementing several router architectures
3. Ability to change pipeline architectures such as 3-stage, 4-stage and 5-stage pipelines in runtime
4. Adding credit signals to each router
5. Improved power model for routers through Orion 3.0
6. Improved area model for routers through Orion 3.0 to measure temperature more accurately in Hotspot 6.0
7. Adding power and area models of several practical processors through McPAT
8. Updating power and area of NoC with each change in router architecture.
9. Adding support for 22, 32, 45, 65, 90 nm manufacturing technology.
10. Calculating leakage current by Temperature Effect Inversion (TEI), taking into account the initial leakage current
11. Measuring leakage current by TEI Through improved Orion 3.0
12. Obtaining temperature feedback from tiles to calculate leakage current by TEI in a specific time interval.
13. Increasing the accuracy of power and thermal measurements in sub-90 nm manufacturing technologies.
14. Report the chip surface temperature once every 100,000 cycles.
15. Bug fixes

First, you need to install SystemC 2.2.0 (Follow the link: https://github.com/systemc/systemc-2.2.0)

1. Change to the top level directory (systemc-2.2)

2. Create a temporary directory, e.g.,

$ mkdir objdir

3. Change to the temporary directory, e.g.,

$ cd objdir
$ sudo apt-get install tcsh
$ tcsh
$ setenv CXX g++

4. Configure the package for your system, e.g., (The configure script is explained below.)

$ ../configure

5. Compile the package.

$ gmake
$ gmake install
$ cd ..
$ rm -rf objdir
$ exit

6. make sure directory "lib-linux" exist! if this name is "lib-linux64", rename it to "lib-linux".

To install the PAT-Noxim, you need to follow a few simple steps.

$ cd PAT-Noxim/bin
$ make
$ make install

Some of the main simulator files are listed in the following table: